A tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to transmit 350 hp at 1,900 rpm. The maximum shear stress in the shaft must not exceed 4 ksi, and the angle of twist is not to exceed 5° in an 8-ft length. Determine the minimum permissible outside diameter if the inside diameter is to be 3/4 of the outside diameter. Answer: Dmin = i in.

A tubular aluminum alloy [G = 4,000 ksi] shaft is being designed to transmit 350 hp at 1,900 rpm. The maximum shear stress in the shaft must not exceed 4 ksi, and the angle of twist is not to exceed 5° in an 8-ft length. Determine the minimum permissible outside diameter if the inside diameter is to be 3/4 of the outside diameter. Answer: Dmin = i in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Dont round off initial values, round off final ans only pls
A Single rivet lap joint is to commect 12 mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².
Read the question carefully and give me right solution with clear calculations
4. Determine the maximum load P that can be applied in the system consisting of a bent bar bolted at both ends through the fiberglass as shown. The diameter of the bent bar is 1/4" Ø, outside diameter of the washer is 7/8" Ø and the thickness of the fiber glass is 3/8". The working shear stress between the fiberglass and the washer is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi. Use 2 decimal places in every solved value. bent bar fiberglass washer bolt cap 7 8. 8 1/14
The assembly consists of three disks A, B and C that are used to support the load of 140 kN. Determine the smallest diameter d, of the top disk, the diameter d₂ within the support space, and the diameter d of the hole in the bottom disk. The allowable bearing stress for the material is (allow)b = 350 MPa and allowable shear stress is allow=125 MPa. B A 140 KN - dz d₂ 20 mm 10 mm
Write complete solution
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
please answer all the questions with complete solutions and draw a proper free body diagram. Thank you
Class work: The two solid cylindrical steel rods AB and BC are welded together at B and loaded as shown in the figure. Knowing that the normal stress must not exceed 175MPa in rod AB and 150MPa in rod BC determine the smallest allowable values of d, and d₂. استنساخ 200 m مكتب المدير مقابل كلية الهندسة مجمع فاطمة 250 mm B 40 kN - d 30 kN
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
The following tubular A36 steel shaft has an inner diameter of 25mm and an outer diameter of 35mm under the following loading condition. Determine the angle of twist of the end V. Consider: GA-36 = 75 GPa 1) What would happen if a solid shaft was used? 2) As a designer, do you recommend a solid or tubular shaft for the loading above? Why?