A pipe with an outside diameter of 300 mm and a wall thickness of 5 mm is subjected to theloads shown. The internal pressure in the pipe is 2MPA. The pipe material has an ElasticModulus = 200GPA ; Poisson's ratio 0.3 and a yield stress of 380MPa.The stress concentrators at point H and K are : Kaxial/pressure=2.1 , Kbending=1.8, Ktorsion/shear=1.6. Find the stresses at point H and K.Find the Von Mises stresses at H and KFind the Safety factors at H and K.Find the deflections at point A in the y-direction and z-direction (if the distance from B to C is2000mm)KВA1,500 mm700 mmP: = 20 kNP, = 15 kN

Stress: It is a force per unit area. As this is cylindrical shape stress on this pipe is mainly hoop…

A pipe with an outside diameter of 300 mm and a wall thickness of 5 mm is subjected to the loads shown. The internal pressure in the pipe is 2MPA. The pipe material has an Elastic Modulus = 200GPA ; Poisson's ratio 0.3 and a yield stress of 380MPA. The stress concentrators at point H and K are : Kaxial/pressure=D2.1, Kbending=1.8 , Ktorsion/shear=1.6. Find the stresses at point H and K. Find the Von Mises stresses at H and K Find the Safety factors at H and K. Find the deflections at point A in the y-direction and z-direction (if the distance from B to C is 2000mm) H K В A 1,500 mm 700 mm P: = 20 kN %3D P, = 15 kN

A pipe with an outside diameter of 300 mm and a wall thickness of 5 mm is subjected to the loads shown. The internal pressure in the pipe is 2MPA. The pipe material has an Elastic Modulus = 200GPA ; Poisson's ratio 0.3 and a yield stress of 380MPA. The stress concentrators at point H and K are : Kaxial/pressure=D2.1, Kbending=1.8 , Ktorsion/shear=1.6. Find the stresses at point H and K. Find the Von Mises stresses at H and K Find the Safety factors at H and K. Find the deflections at point A in the y-direction and z-direction (if the distance from B to C is 2000mm) H K В A 1,500 mm 700 mm P: = 20 kN %3D P, = 15 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam pipeline measures 20 m at a temperature of 20 °C. The pipeline carries superheated steam at a temperature of 300 °C. If 80% of the possible expansion of the pipe is prevented from taking place, find the stress induced in the material of the pipe having E =210 kN/mm 2 and coefficient of thermal expansion = per °C.
A brass pipe has an internal diameter of 400mm and a metal thickness of 6mm. A single layer of high tensile wire of diameter 3mm is wound closely around it at a tension of 500N. Find the stress in the pipe when there is no internal pressure. (b) the maximum permissible internal pressure in the pipe if the working tensile stress in the brass is 60MN/m^2. (c)) The stress in the steel wire under condition b. Treat the pipe as thin cylinder and neglect longitudinal stresses and strains. Young mudulus of steel=200GN/m^2 and for brass =100GN/m^2
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy= 41 MPa, Sy = 11 MPa, and S=-44 MPa. (a) Determine the principal stresses (o,l > 02) and the magnitude of the maximum in-plane shear stress Tmax acting at the point... (b) Find the smallest rotation angle 0, (counterclockwise is positive, cločkwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: OpI = MPa. Op2 = MPa. Tmax | MPa.
The stepped shaft shown in the figure isrequired to transmit 600 kW of power at 400 rpm.The shaft has a full quarter-circular fillet, and thesmaller diameter D1 =100 mm.If the allowable shear stress at the stress concentrationis 100 MPa, at what diameter D2 will thisstress be reached? Is this diameter an upper or alower limit on the value of D2?
A thin-walled cylindrical pressure vessel of inner radius r = 0.6 cm and a thickness of 0.06 cm is subjected simultaneously to internal gas pressure p = 3.5 MPa, a compressive force F = 800 N acting at the ends, and a torsional load of 25 N · m (see figure). Determine the following quantities (a) the principal stresses at a point H on the surface of the vessel and the absolute maximum shear stress; (b) the normal strain along x-axis (ɛx) and the shear strain (yxy) at the same point H. See the established Oxy coordinate system. The Young's modulus of the material is 200 GPa and the Poisson's ratio is 0.3. Hint: the cross-section of the vessel can be regarded as a hollow tube and the cross-section area can be calculated as 1(0.00662 – 0.006²). You can do the same treatment for the polar moment inertia. 25 N· m F F H X 25 N· m
A steel pipe of length L= 3 ft, outside diameter d₂- 10 in., and inside diameter dy = 5.1 in. is compressed by an axial force P= 107 kips. The material has = Poisson's ratio v=0.30. Determine the increase in thickness.
Еx10: A hollow steel cylinder (length l=300mm) inside diameter d=150mm wall thickness t=3mm is filled with concrete and compressed between rigid plates by load P=500KN, find the stresses and the shortening of the cylinder if Es=200KN/mm for the steel and Ec =20KN/mm for the concrete?
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and Sy = 250 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 46°.
A spherical tank of diameter 1.2 m and wall thickness 50 mm contains compressed air at a pressure of 17 MPa. What is the value of tensile stress? (Assume E = 210 GPa, v = 0.29)
Problem 3 A large spherical tank (see figure) contains gas at a pressure of 3.5 MPa. The tank is 20 m in diameter and is constructed of high-strength steel having a yield stress in tension of 550 MPa. (a) Determine the required thickness of the wall of the tank if a factor of safety of 3.5 with respect to yielding is required. (b) If the tank wall thickness is 100 mm, what is the maximum permissible internal pressure? (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.)
PROBLEM 3. The stress condition at one point in the tail region of the National Combat Aircraft is shown in the figure. (a) Calculate the principal stresses (b) Calculate the maximum in-plane shear stress and the average normal stress by analytical method and plotting the Mohr's circle. For each case, determine the element orientation and plot the stress state. (c) Calculate the maximum absolute shear stress at the same point. 40 MPa TAI 200 MPa 80 MPa
Q4/ cylinder has an internal diameter of 200 mm, has walls 3 mm thick and is 1.2 m long. It is found to change in internal volume by 11x10 m' when filled with a liquid at a pressure p. If E=200 GN/m? of hoop and v-0.25 determine the values and longitudinal stresses?