Read1483%A pipe with a cross sectional area of 5x10 m is delivering oil at a rate of Ix10 m/s at apressure of 700 kPa. This pipe connects by a gradually expanding pipe to a main of crosssectional area of 3x10 m which runs 2 m above it. Calculate the pressure in the main,neglecting losses to friction. The oil has a density of 890 kg/m.(1)Answer each of the following for an electropneumatic circuit that operates a single actingcylinder with direct control.(i)Sketch the pneumatic and clectrical circuit that uses the logic OR operation to extendthe cylinder.(ii)Sketch the pneumatic and cleetrical circuit that uses the logic AND operation to extendthe cylinder.(2.5ks)Air at a pressure of 6 bar gauge pressure has a volume of 3m'. The volume of the air isallowed to increase to 5m' at constant temperature. What is the air gauge pressure at the newvolume? The atmospheric pressure is 101.85kN/m.(h)For a vertically mounted hydraulic actuator with an overrunning load, what is the majordisadvantage of using a counter balance valve to prevent a weight from falling uncontrollablyand how can it be overcome?Air

Answered: Image /qna-images/answer/b0e95e30-5248-4553-8a8c-c0e33ceed13b.jpg

A pipe with a cross sectional area of 5x10 m' is delivering oil at a rate of 1x10 m/s at a pressure of 700 kPa. This pipe connects by a gradually expanding pipe to a main of cross sectional area of 3x10 m which runs 2 m above it. Calculate the pressure in the main, neglecting losses to friction. The oil has a density of 890 kg/m.

A pipe with a cross sectional area of 5x10 m' is delivering oil at a rate of 1x10 m/s at a pressure of 700 kPa. This pipe connects by a gradually expanding pipe to a main of cross sectional area of 3x10 m which runs 2 m above it. Calculate the pressure in the main, neglecting losses to friction. The oil has a density of 890 kg/m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

This is merely a past paper question please assist
The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter steel pipe at a rate of 10 m3 / hr. The pipe length is 35m and there are 2 elbows. Calculate the power requirements of the pump. The properties of the solution are density 975 kg / m3 and viscosity 4x 10-4 Pa s. a. Reynold number = Answer b. Loss of Energy along the straight pipe = Answer J / kg. c. Losing Energy at curves = Answer J / kg. d. Total energy to overcome friction = Answer J / kg. e. Energy to increase water according to height = Answer J / kg. f. The theoretical energy requirement of the pump ethanol / second = Answer J / kg. g. Actual pump power requirement = Answer watt.
A 500 mm diameter pipe gradually reduces to 20 mm diameter and the gradually enlarge to its original size. Given the pressure at the base of the convergence of 0.60 MPa with a flow of 0.08 cu. m/s, 1. What is the velocity at point 1? 2. What is the velocity head at point 2? 3. Neglecting the head loss, the pressure of the smallest section is?
Prob 4.Draw fbd.
M1
6.5 BELLOWS 6100mm The horizontal elbow is joined by bellows to the rest of the piping system and it transports water. Determine the X and Y components of the force needed to keep the elbov in posi- tion. The pressure at A and B is 200 kPa, the flow rate is 30 L/s and the pipe diameter is 100 mm. 6.6 Water flows at a rate of 0,055 m³/s through a piping system and then issues from the pipe of 50 mm diameter into the atmosphere. Ø150mm Ø50mm Ignore losses in the pipe and determine the force required at the flange to keep the nozzle in position. (Hint: first determine the pressure at A with Bernoulli's equation.)
A pump is required to transfer water at the rate of 350 kg/s from an open sump to an open storage tank located 30m above the pump. The sucLon pipe is 350mm in diameter and 12m in length and the delivery pipe is 550mm in diameter and 40m in length. Calculate:(a) The maximum height at which the pump may be placed above the sump, so that pressure at the inlet is not less than -80 kPa (gauge) (b) the energy to be supplied by the pump per unit mass of water transferred (c) The input power required by the pump, which is 60 % efficient
Water at 80°F flows from a storage tank through 618 ft of 6-in Schedule 40 steel pipe, as shown in the figure. Taking the energy loss due to friction into account, calculate the required head hin feet above the pipe inlet to produce a volume flow rate of 1.65 ft³/s. (round the final answer to three significant figures) h 6-in Schedule 40 steel pipe pipe length
Please solve and answer the question correctly please. Thank you!!
(a) An open domestic hot water circuit for a residence is to cater for three bathrooms each having two hot water outlets of diameter 20mm. All outlets are connected to a single main line pipe running down the service stack shaft. After factoring all friction losses and the gravitational head, the system is pressurised such that the ideal flow rate per outlet is 14 l/min. What is the ideal main pipe diameter size if the fluid velocity in the main line pipe and the outlet branches is to be kept the same and (i) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 0.5 is assumed (half of the taps open at any point in time) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 0.75 is assumed (ii) (ii) A diversity factor (i.e. the number of outlets open to atmosphere over total number of outlets installed) of 1.0 is assumed (All taps open at any point in time)
In the system shown, the pipe is commercial steel, the inlet andoutlet is sharp edge and the flow rate is 125 L / s. Determine the "K"from valvule
Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s