2. Water at 10 C is flowing10 pointsfrom point A to point Bthrough the pipe, as shown inthe figure, at the rate of O.37m3/s. If the pressure at A is66.2 kPa, determine thepressure at B, in kPa,assuming no frictional losses.600-mminside diameter4.5 mFlow300-mminside diameter

E. Water at 10 C is flowing rom point A to point B hrough the pipe, as shown in he figure, at the rate of O.37 n3/s. If the pressure at A is »6.2 kPa, determine the pressure at B, in kPa, Issuming no frictional losses. 600-m. inside dian

E. Water at 10 C is flowing rom point A to point B hrough the pipe, as shown in he figure, at the rate of O.37 n3/s. If the pressure at A is »6.2 kPa, determine the pressure at B, in kPa, Issuming no frictional losses. 600-m. inside dian

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Friction in pipe cause O 1. reduction in potential energy 2. Reduction in velocity 3. Reduction in pressure 4. Increase in pressure
Examples & The Inlet to pump is 10.50m above the bottom of sump from which it draw water through a suction pipe. If the pressure at the pamp inlet is not to fall bellow 28 kN/m² absolute, work out the minimum depth of water in the tank 6.019 m O 15m 0 3.019 m O 9.019 m O 1.019 m O
Q2 Runner shaft. Figure shows a Kaplan turbine. The flow of Ha water rotates the runner at 200 rpm to generate power. The 28.575 mm diameter runner shaft is to be supported by the Water in Water in bearings at "a" and "b". The runner mass is 80 kg and an 800 N downward axial force is exerted by the water flow at the CG point of each blade. There are 4 blades. Runner a) Choose appropriate tapered roller bearing at b. b) Choose suitable ball bearing at a. c) What will be the combined reliably of both bearings? Consider: Bearing life = 30kh, Application factor = 1, Reliability goal = 92%
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
Q4:-Locate the vertical axis of rotation and the speed of rotation (r/s) of the U-tube of fig.(4),as that the pressure of liquid at points A and B at (zero gauge)
The power 338 W is required to transmit 5 x 10-3 m3/s of water. Find the loss of head due to friction in a pipe. The head loss due to friction (in m of water)
If you have a closed system that is filled with water on 2bar, the pump is selected for pressure losses due friction of the pipes(1bar) 1/ why don't we have to take pressure losses due height in account? 2/ what is the pressure at 100 m height inside the system? When the pump stops? And when the pump is circulating, prove your answer figure in image
P₁ = 80 kPa B 3 m PB = 50 kPa Calculate the friction head loss for a water Q-1 flowing from point A to B.
Find the difference in pressure head and velocity of flow of an ail through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 116 mm. Take co-efficient of the pitot tube ("L shaped measuring instrument) as 0.97 and sp. gr of ail = 0.85 (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr)%3D
A pitot tube directed into a water stream having velocity 2.3 m/sec. Its gauge difference of 30 cm on the water mercury manometer. Find the coefficient of velocity.
B4. An orifice meter with orifice area 878 mm2 is inserted in a pipe of area 1756 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 60 cm of mercury. Find the rate of flow of oil of sp. gr. 0.85 when the co-efficient of discharge of the orifice meter = 0.64. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) Head of water (in m) The discharge of water through pipe (in Litres/sec)
В4. An orifice meter with orifice area 1039 mm2 is inserted in a pipe of area 2078 mm2 .The pressure difference measured by a mercury oil differential manometer on the two sides of the orifice meter gives a reading of 60 cm of mercury. Find the rate of flow of oil of sp. gr. 0.9 when the co-efficient of discharge of the orifice meter = 0.52. Head of water (in m) The discharge of water through pipe (in Litres/sec)