A pipe network with two loops is shown in Fig. 11.20. Determine the flow in each pipe for an inflow of 5 units at the junction A and outflows of 2.0 units and 3.0 units at junctions D and C, respectively. The resistance R, for different pipes are shown in the figure. A R= 120 units B 5.0 units R= 200 units R= 300 units R= 400 units D R= 150 units 2.0 units 3.0 units Fig. 11.20 A pipe network

Q: 2 3 Example 11.3: Air at a flow rate of 1 m/s flows through a fitting whose cross-sectional area…

A: Please see the attached image for the answer.Explanation:

Q: 8 In a 2 m long pipe the cross-sectional area A-0.4 m². At a given instant a discharge of 0.48 m/s…

A: Given that: length of pipe = L = 2 mcross-sectional area of pipe = A = 0.4 m2Discharge =Q = 0.48…

Q: i need a explanation about all formulas using in this picture and Where should I use each formula?…

A: Steps to Use the Formulas in the Duct System:Calculate the area of the sport area using A=L x…

Q: 04: For the piping system, compute pressure at A, and mid pipe 2. If pipe (3) & pipe (4) havi equal…

A:

Q: Q₂/Suppose in Figure 2, the lengths and diameters of pipe 1 is 300 m x 0.3 m, Pipe 2 is 150 m x 0.2…

A: Given:Pipe 1: L1=300 m, d1=0.3 mPipe 2: L2=150 m, d2=0.2 mPipe 3: L3=250 m, d3=0.25 mWater…

Q: A fluid is pumped at a rate of 0.00156 m /s through a 0.025-m-diameter pipe to fill a water tank as…

A:

Q: 34. A pressurized tank contains saturated water. A frictionless valve on the pipe is now opened to…

A: Given Data:Note:

Q: 10 in discharge pipe is attached to a certain storage. The head loss from the surface to the…

A: Given:d=10 in =0.254 mHl=8 ft =2.4384 mZ1=15 ft =4.572 m

Q: Pump head, hp, can be formulated as, h, = 22 - z1 + hm + he Where, E h = EK and hy = Table 1: Minor…

A: a)  Volume flow rate =0.006 m3/s ( given) Radius = 2cm = 0.02m Cross section area= 3.14 × 0.022…

Q: The Alaska pipeline conveys crude oil 800 miles across the state of Alaska from Prudhoe Bay to…

A: Data given -  L = 800 miles = 800×5280 ft  di = 48 inch = 4ft  t = 0.5 inch  Outer diameter of…

Q: On a single plot, plot three curves that show the relationship between the pressure generated by the…

A:

Q: A fuel line is to convey octane over a distance of 35 ft. The required flow rate is 0.3 ft3/s and…

A: Given data: L=35 ft=10.668 mQ=0.3 ft3/s=0.00849505 m3/s∆P=75 kPaf=0.002 Need to determine the size…

Q: 49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and…

A: Given:To find:(a) Total pressure drop.(b) Diameter of the equivalent pipe.

Q: A 140 m long pipeline runs between two reservoirs, both ends being under water, and the intake end…

A: Given:Length of the pipe, L=140 mDifference between the water levels in the two reservoirs, H=40 ma…

Q: Please give a detailed explanation, Don't use chatgpt.

A: Given data:Volume, V = 20gal = 0.0758 m3d1 = 1 inchd2 = 0.52 inchAverage velocity, v = 8 ft/s…

Q: 3. Find the area needed for an air filter that is 1 cm thick and has a permeability of 10-10 m?. The…

A:

Q: Describe the methodology for obtaining the pump curve in a project, where data are collected at five…

A: A pump curve is a graphical representation of a pump's performance based on testing conducted by the…

Q: Each of the two circular pipes carries water at 65 °C flows at a Reynolds Number of 3.8× 10^4.…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.