A pair of 135-N forces is applied to the handles of the small eyelet squeezer. The block at A slides with negligible friction in a slot machined in the lower part of the tool. Neglect the small force of the light return spring AE and determine the compressive force P applied to the eyelet. 135 N 54.5 mm 47 mm C B 12 mm ACWwwwaE D 7.00 mm 135 N Answer: P =

Q: Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing…

A: TRUSS:- is a rigid structure in which all he members are subjected to either axial or  tensile or…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: Determine the magnitude of the clamping forces (in pounds) exerted on the nut along line aa when two…

A: Given: The force acting on handle, F = 64 lb

Q: A turnbuckle, which is used to adjust tension in cables, is subjected to tension T=184.7 N as shown.…

A: Given data: The tension in the cable, T = 184.7 N. The lead of screw, L = 0.005 m. The nominal…

Q: 7. In the wedge shown in the figure. Determine the largest angle that will cause the wedge to be…

A: As per given question  We have to determine the largest angle

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: Q2/ Determine the forces at the pin ? joint (F) and the roller support (G) 30KN 20 KN 2m B 2m D 2m G…

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: Determine the value offorce Pand F acting along the bars maintaining equilibrium of pin A. ans.: P =…

A:

Q: Uad an r sheets Tw Pand 0 edshown in Fig to an ac reecton Knowng that the connecton isn eguitrum and…

A:

Q: This is a question of one of the practice problems for this topic. After obtaining the forces in…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: Draw a FBD of pulleys E & D of the bar AD shown. Assume all hinges to be smooth & neglect the weight…

A:

Q: when the beam is horizontal. For W-90 lb and the stiffness of the spring k-313 lb/in, determine the…

A: The free-body diagram is-

Q: Part A If the 5.6-kg block is suspended from the pulley B and the sag of the cord is d = 0.15 m,…

A:

Q: The wheel of radius 300mm is being stopped by a block brake shown in the figure. A triangular…

A: We have to determine smallest distribution load.

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: Q2/ Determine the forces at the pin ? joint (F) and the roller support (G) 30KN 20 KN 2m B 2m D 2m

A: find the reaction at F and G.

Q: The wagon has a mass of 19.5 kg and centre of mass at G. Both the front and rear wheels are locked,…

A:

Q: PA Q Search 250 mm B H M 70 mm- 30 mm C

A:

Q: Determine the axial force in member BC of the frame. Note the joint Dis a sliding pin. D. Dimensions…

A:

Q: Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN…

A: Given: P1 = 2 KN P2 = 1.5 KN To find: FCD and FGF

Q: Block A wieght lo k and blocK B wieghnt 20 RN, the coeficient of Priction between Block A and Bis…

A: given: weight of A=10KNWeight of the block B=20KNCoefficient of friction between A and…

Q: Determine the forces in members CD, CJ, and DJ.

A:

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a 2.9 ft, b-2.4ft, r - 6 in. "" W…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A:

Q: he wheel is subjected to a torque of M-55 N-m. The oefficient of kinetic friction between the band…

A:

Q: An axial load of 160 lb is applied to the end bear- Fig. ses place over an annular ring of radius 4…

A: Given that, Axial load applied, P=160 lb,Inner radius of ring, r=4 in,Outer radius of ring, R=7…

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

A:

Q: Determine the compressive force exerted on the stone by vertical load P = 65 N applied to the toggle…

A:

Q: 19. What is the equilibrium angle if the 1-1bm rod is 24 in long? Assume all surfaces are…

A:

Q: An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley…

A: Given data θ=2.89 radv=29.36 m/secA=366 mm2ρ=1000 kg/m3μ=0.3 Here, v is the velocity, A is the area…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.