Determine the tension in the cable and the horizontal and vertical components of reaction of the pin A. The pulley at D is frictionless and the cylinder weighs 83 lb.( Bovce 1) Figure 10f1 Part A Determine the tension in the cable. Express your answer to three significant figures and include the appropriate units. Submit Part B Value A..A, Request Answer Determine the horizontal and vertical components of reaction of the pin A. Assume that the positive and yes are directed to the sight and upward, respectively Submit Express your answers using three significant figures separated by a comma. Assume that the positive and yaxes are directed to the right and upward, respectively VAX vec Units Request Answer ? lb

Determine the tension in the cable and the horizontal and vertical components of reaction of the pin A. The pulley at D is frictionless and the cylinder weighs 83 lb.( Bovce 1) Figure 10f1 Part A Determine the tension in the cable. Express your answer to three significant figures and include the appropriate units. Submit Part B Value A..A, Request Answer Determine the horizontal and vertical components of reaction of the pin A. Assume that the positive and yes are directed to the sight and upward, respectively Submit Express your answers using three significant figures separated by a comma. Assume that the positive and yaxes are directed to the right and upward, respectively VAX vec Units Request Answer ? lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data is referring to a screw jack. The vertical load on the screw = 20kN Force applied at the lever end whose length = 80cm The mean radius of the screw = 2.5cm Pitch of the screw =1cm Co-efficient of friction between the screw thread and the nut = 0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
Please don't provide handwritten solution ....
Please help. Written on paper not typed on computer please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
8. A 3000 N block is placed on an inclined plane as shown in Figure. Find the maximum value of W for equilibrium if tipping does not occur. Assume coefficient of friction as 0.2. Frictionless Pulley 3000 N W 30°
SOLUTION: • Determine values of friction force and normal reaction force from plane required to maintain equilibrium. Example 100 N • Calculate maximum friction force and compare with friction force required for equilibrium. If it is greater, block will not slide.
Question 1The 150 kg bucket is suspended from a cable on the wooden frame. The frame is supported by a pin at E (which is connected in double-shear) and reinforced by a strut BD and a steel cable CF as shown in Figure 1 (attachment). The effect of friction at joints and support, the self-weight of the frames, and the deformation of the cable are neglected. (a) Sketch the free body diagram. (b) Determine the internal force in cable CF and reaction forces at joint E. (c) Determine the resultant internal loadings acting on section a-a. (d) Determine the diameter of the pins at E if the allowable shear stress is τallow = 72 MPa.The pin is subjected to double shear.
#2 Subject: Statics of Rigid Bodies Last digit # to use: 1 Please answer logically with complete solution (and FBD hopefully), thank you so much!!!!!!
Please provide the correct solution, and include free body diagram.
can I have the solution of this problem ,,,,,, and the final answers are theses
%£9 lI. 4G 11:9 1st class / 2021- 2022 PROBLEMS 1 - A ( 200 N ) weight of the block shown in fig. is supported by a pin and bracket at ( A ) and by a cable ( BC ). Determine the reaction at ( A ) and the tension 30 in the cable 0.75 2 - The 200-N force produces a torque (moment) of 40 N.m about the axis of the bolt in order to tighten the hexagonal nut. Find the forces between the smooth jaws of the wrench and the nut if contact occurs at the corners A and B of the hexagon. 3 - The pin at A can support a maximum force of 3.2 KN . What is the coresponding maximum load L which can be supported by the bracket ? 4 - A block placed under the head, of the claw hammer as shown greatly facilitates the extraction of the nail. If the 200-N pull on the handle is required to pull the nail calculate the tension T in the nail and the magnitude A of the force exerted by the hammer head on the block The contacting surfaces at A are sufficiently rough to prevent slipping Alamarah University College…
A pair of 135-N forces is applied to the handles of the small eyelet squeezer. The block at A slides with negligible friction in a slot machined in the lower part of the tool. Neglect the small force of the light return spring AE and determine the compressive force P applied to the eyelet. 135 N 54.5 mm 47 mm C B 12 mm wwwmE 7.00 mm 135 N Answer: P = |N
Problem 07.093.b - Maximum tension of cable with level supports Determine the maximum tension in the cable.