Answer with complete and detailed solution Determine the axial force in member BC of the frame. Note the joint Dis a sliding pin.Dimensionsin mm16 N-m70

Answered: Image /qna-images/answer/484d6b92-0f25-48e4-b057-fd64e78f5f4b.jpg

Answered: Determine the axial force in member BC…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

Determine the force supported by the pin at A for an 80-N squeeze on the handles of the pliers. (Hint: Draw free body diagram of each handle) -35 mm- 95 mm- 80 N 80 N
6
Take a "cut" at H (draw a proper FBD) and determine the forces at H.
The round stepped shaft (diameters d and D) shown below is a design for an exoplanet rover wheel axle. Assuming the wheel is stuck, a torque from the motor is transmitted to the axle but it is not rotating. The reaction of the weight of the rover on the ground and the torque the wheel applies to the ground are represented by the force F acting in the center of the wheel hub (not shown) at point C. There is a sharp fillet at B with radius r shown below. Bearings are shown at point A and next to point B. You may assume the bearing at B resists the bending moment caused by the force F and acts like a fixed reaction. В A L2 L1 T L3 - ØD Ød R. r F SUBMIT ANSWERS HERE: Paramete Parameter Value Value SUT (tension) 400 MPa | L1 400 mm Suc (Compression) 600 Мра L2 200 mm Sy 380 MPа L3 100 mm 600 N-m ø d 40 mm F 0.2 kN ø D 55 mm R. r 8 mm
.
F8-5. Determine the horizontal displacement of joint D. AE is constant. Use the principle of virtual work. F8-6. Solve Prob. F8-5 using Castigliano's theorem. 6 kN ID -3m- 3'm -6 kN Probs. F8-5/6
Solve Prob. 7.29 if =0.
Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 84 N and (a) e = 30°, B = 25° and (b) e = 16°, B = 27° %3D F BI B L--n Answers: (a) Fn= N, F = N (b) Fn= N, F = the tolerance is +/-2%
Show all Free Body Diagrams A) Use the Method of Joints to find the forces in AB and BC. Indicate whether its tension or compression.
Determine the magnitude of the pin reactions at Band Cif W = 1720 lb. 3.7' 3.7' 2.0' Answers: B = i Ib C = Ib
Q-4. Determine the "Horizontal Displacement" of Joint "A of the below given frame by using the "Method of Virtual Forces". 6 ft B 200 lb -6 ft- 8 ft
66 kN P৭:1 Asiacell l. کتاب میریام میكانيك هندسي.pdf 80 N Problem 4/69 4/70 Compute the force supported by the pin at A for the slip-joint pliers under a grip of 100 N. 270 mm of the 450 60 mm 100 N 100 N Problem 4/70 4/71 Determine the force supported by the roller at E. Ans. E = 150 N D 0.3 m E 0.3 m 200 N 0.6 m 0.3 m F 1.2 m Problem 4/71

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS

Determine the axial force in member BC of the frame. Note the joint Dis a sliding pin. D. Dimensions in mm 60 16 N-m 70 OST