Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz plz plz. Determine the force in member BE of the loaded truss. Enter a positive number if in tension, negative if in compression.11'B14'15°15°FE11'15°1.0 L1.7L15°45°AAnswer: BE = i!L45°D

To find the output for the given circuit, let's interpret the symbols:- "10>" indicates an input…

Answered: Determine the force in member BE of the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

You’re testing a system that involves a fan, water pump, and compressor. The components are turned ON in sequence and sensor readings are taken, as per a written protocol that you’re following. The system is running as expected after the fan and water pump are turned ON. However, when you turn ON the compressor, it runs for about thirty seconds then stops, consistently. Swapping out the compressor for a different one seems to solve the problem. What could have been the issue with the bad compressor?
This problem is (16.23) from a book "Thermodynamics and Statistical Mechanics An Integrated Approach by M. Scott Shell"
Don't Use Chat GPT Will Upvote
Consider the basic EOQ model. We want to know the sensitivity of (1) the optimal order quantity, (2) the sum of the annual order cost and the annual holding cost (not including the annual purchase cost cD), and(3) the time between orders to various parameters of the problem. a. How do (1), (2), and (3) change if the setup cost K decreases by 10%? b. How do (1), (2), and (3) change if the annual demand doubles? c. How do (1), (2), and (3) change if the cost of capital increases by 10%? (For this part, assume that the storage cost s is zero.) d. How do (1), (2), and (3) change if the changes in parts a, b, and c all occur simultaneously?
A very convenient and compact method of representing the process dynamics of linear systems involves the use of _______ and block diagrams. _______ can be obtained by starting with a physical model. ( Note that the two _______ refer to the same term).
Task Page Static Temperature (mixture) line-19 Run Calculation 2.72e+02 Check Case... Preview Mesh Motion... Time Advancement Туре Method 2.71e+02 Fixed User-Specified Parameters 2.70e+02 F Line/Rake Surface Name line-19 Static 2.69e+02 Options Number of Points Temperature (mixture) O Line Туре 10 Line Reset 2.68e+02 (k) End Points x0 (m) 0 x1 (m) 0.032 2.67e+02 yo (m) 0.04 y1 (m) 0.04 z0 (m) z1 (m) 0 Select Points with Mouse 2.66e+02 0.005 0.01 0.015 0.02 0.025 0.03 0.035 Save Close Help Position (m) Calculate |-Q|Q | R - O selected
Q: a) Generally, if you are asked to find any physical quantity (e.g. pressure, temperature, flow rate), what steps you will follow in order to find that physical quantity. b) Let say you are asked to measure the tempreture of a room, what sensor will you use? What will be the criterion for selecting a specific sensor in this case? And how you display the results with the help of any controller (consider Arduino as a controller)
An engineer is designing a transfer line. The line has 15 stations. Stations 1 through 10 should have the same reliability. Each station is expected to operate approximately 1000 cycles between failures. The last 5 stations are expected to break down about once every 600 cycles. Repair times will vary but should average about the equivalent of 12 cycles in duration. a. Find the availability of the line. b. Suppose you could add one buffer of size 20. Where would you place this buffer? Find the increase in availability
You are the mechatronics engineer of a manufacturing plant. You decide to perform an analysis on a robot arm of the assembly line with the objective of optimizing its performance. After taking several readings of the speed of the arm’s end effector, you approximate its velocity to the function given below. v(t) = -t4 + 5t3 - 7t2 + 3t + 0.22 0 =< t =< 3 where the velocity is in ms-1 d) Knowing that the distance travelled by an object is the area under its velocity-time graph, determine the distance travelled by the end effector on the interval 0 =< t =< 1 by using the mid-ordinate rule. Simpson’s rule correct to 3 decimal places using four intervals. e) Calculate the same distance as in (d) above by using the appropriate definite integral. f) Compare the distances you calculated in (d) and (e) above and comment on the accuracy of the two methods you used in (d)
hand written i'll rate
i need the answer quickly
Fast plzzzzzz hand written otherwise downvote....plz solve it within 30-40 mins I'll give you multiple upvotes HAND WRITTEN

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Determine the force in member BE of the loaded truss. Enter a positive number if in tension, negative if in compression. 11' B 14' 15° 15° F E 11' 15° 1.0 L 1.7L 15° 45° A Answer: BE = i !L 45° D