The signboard truss is designed to support a horizontal wind load of 700 lb. If the resultant of this load passes through point C, calculate the forces in members BG and BF. The forces are positive if in tension, negative if in compression. 700 lb Answers: BG= i BF= i C B 10' /G -105 7' 7' F 7' lb lb

Q: Determine the magnitude of the pin force at A. Assume W - 615 lb, a = 3.2 ft, b - 2.3 ft, r = 9 in.…

A:

Q: Specify a cylindricity tolerance of .0004 for the largest cylindrical surface on the part in the…

A:

Q: Which position tolerance is shown in below’s technical drawing? Explain the meaning (that is the…

A: Which position tolerance is shown in below technical drawing?Explain the meaning (that is the…

Q: Determine the force in each member of the loaded truss. The forces are positive if in tension,…

A: Given data: ◆ The force applied at the joint D: F = 2140 N ◆ The dimensions of truss: a = 3.3 m, b =…

Q: Determine the resultant R (single equivalent force) of the three forces acting on the simple truss.…

A:

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

A:

Q: A PVC (k = 0.20 W/m-K) pipe is 2.5 m long and has inner and outer radii of 2.3 cm and 3.3 cm,…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: On the part in Q1, show the size and shape of the tolerances zone. Lecture 5 Q1 On the part below,…

A:

Q: A slip gauge setting height  of 65.215mm is observed and an angle of  480 is found during the…

A: Given data, Slip gauge height  (h) = 65.215 mm Angle (€) = 48° Find  Length of sine bar (L)

Q: ne 1/2-inch diameter pin in the drawing below is required to be perp ature A within tolerance of…

A: A feature control frame is used to show the conditions and tolerances of the dimension of the part…

Q: A slip gauge setting height 53.155 mm is observed when a sine bar of the length 127 mm is used…

A: Angle using sine bar and slip gauge is find out by Angle = Sin-1(slip gauge height/ length of sine…

Q: 2. Nominal size is 40mm, the clearance is between 24µm and 92µm, the span of the clearance fit is…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Apply the necessary symbology to establish the required tolerance and datum features to control the…

A:

Q: A flow of steam at 12 MPa, 600°C enters a two-stage turbine as shown in the image below. The…

A:

Q: The cross section of a bearing block is shown in the figure by the shaded area. Calculate the moment…

A:

Q: Find the tolerance and fit type of Ø 60 H7k6,

A: given: nominal size, D=60mm tolerance hub: H7 tolerance shaft: k6 so for tolerance hub: H7, the…

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance?…

A: Total positional tolerance shows us the maximum allowable deviation of a feature from its true…

Q: 3. If the tolerance applies at MMC then a possible O indeterminant bonus O LMC zero tolerance…

A: given = fill in the blanks

Q: In a limit system, the following limits are specified for a hole and shaft assembly: Hole = 30…

A: Given data: -  The limits of the hole is Dh=30+0.00+0.02 mm. The limits of the shaft is…

Q: An in-line cam with a roller follower is to raise the follower by 1.5 in with harmonic motion while…

A:

Q: Find the taper angle, in radians, for a workpiece if a sine bar method was used. The stacked height…

A: Sine Bar is used to measure taper angle by using gauge lengths and length of sine bar. It is the…

Q: Refer to the figure below. What is the MMC, LMC and geometric tolerance for the Hole and Pin: a.…

A:

Q: If the pin in the drawing below is produced at Ø.498, what is its total positional tolerance? C…

A: Given data as per the question Pin diameter =0.498

Q: Tolerances for a hole and shaft assembly having a nominal size of 50 mm are as follows: Hole = 40…

A: Basic size=40mm Tolerance of hole=0.06-0=0.06mm Tolerance of Shaft=-0.015+0.07=0.055(may be the…

Q: A B D (a) If the gap, w, must be at least 0.015 in for the proper functioning of the assembly, what…

A:

Q: Determine the force in each member of the figure shown below and state if the members are in tension…

A:

Q: Specify a flatness tolerance of .004 for the top surface of the part in the drawing below. A. B. C.…

A:

Q: The free-body diagram of the entire truss is shown. Find the force ly. A Answer: ly= L B L K C L D L…

A: Draw the free-body diagram which is given.

Q: Determine the support reactions at A and E.

A:

Q: -0.05 m. The dimensions for the shaft size are 020 -0.10 1. mm and the hole size are O20 Find the…

A:

Q: I need help with numbers 4 and 7. They are both wrong.  One the part attached what is the maximum…

A:

Q: The 590-kg uniform I-beam supports the load shown. Determine the reactions at the supports.

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.