A marine type flange coupling is used to transmit 3.75 MW at 150 r.p.m. The allowable shear stress in the shaft and bolts may be taken as 50 MPa. Determine the shaft diameter and the diameter of the bolts. [Ans. 300 mm ; 56 mm|

A marine type flange coupling is used to transmit 3.75 MW at 150 r.p.m. The allowable shear stress in the shaft and bolts may be taken as 50 MPa. Determine the shaft diameter and the diameter of the bolts. [Ans. 300 mm ; 56 mm|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 37. What factor of safety is needed for a 1.998 in diameter shaft with an ultimate * strength of…

Q: For the two force systems shown below, find the following: 1. The resultant force and its…

Q: A solid stainless steel [G= 12,500 ksi] shaft that is 30 in. long will be subjected to a pure torque…

Q: Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference.…

A: Turning operation is the manufacturing technique that is done on a lathe machine. In this operation,…

Q: A solid shaft with diameter 3 in. is to transmit 139 hp. If the shaft shownis rotating at 300…

A: Given Power, P = 139 hp Diameter, d = 3 in = 0.0762 m Speed, N = 300 rev/min Find Shear…

Q: The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a.…

A: Given data: Diameter of the solid shaft, D= 10mm Shear stress, s=75MPa=75N/mm2

Q: Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at…

Q: A marine type flange coupling is used to transmit 3.75 MW at 150 r.p.m. The allowable shear stress…

Q: A compound shaft drives several pulleys, as shown. Segments (1) and (2) of the compound shaft are…

Q: i kullanılmıştı ancı bölgesind

A: Given: Power to be transmitted = 0.67 KW Rotational speed = 900 KPM Gear width = 20 mm Yield…

Q: 5. Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for…

Q: Q.1 Design a compression coupling for a shaft to transmit 2000 N-m. The allowable shear stress for…

A: Answer: Given, T = 2000Nam = 2000 x 103 N - mm τ= 50 MPa σ t = 90MPa No ,of bohts , N = 6…

Q: (3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are Ø120mm, 100mm…

Q: 2. A brass sleeve with an inner diameter of 200mm and an outer diameter of 300mm is pressed onto a…

Q: A flanged bolt coupling consists of eight – 10mm diameter steel bolts on a bolt circle 500mm in…

Q: A 500 mm pulley running at 400 rpm drives another pulley of the same diameter by means of a 12 mm…

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

Q: 8.6 (A). A hollow low carbon steel shaft is subjected to a torque of 0.25 MN m. If the ratio of…

A: According to the given data T=0.25MN.m τ=70MN/m2 k=1/3=0.333 G=80GM/m2 We need to find Diameters of…

Q: Identify the flange thickness (in mm) of a flange coupling having 6 bolts, that is 10-mm in…

A: Write the expression of torque transmitted to the flange. Tflange=nd1tfσcfD12 ......…

Q: The assembly is subjected to a torque of (a) T = 90 Nm (b) T = 200 Nm. If the Factor of safety for…

Q: Calculate the shaft diameter necessary to support a combined maximum bending moment of 2000 Nm, and…

Q: A drive shaft is made of solid steel. It is desired to transmit 2.5 hp at 150 rpm. The allowable…

Q: Design and draw a protective type of cast iror flange coupling for a steel shaft transmitting ? kW…

A: Machine Design

Q: proper key for the joint shown in figure E rque of T= 180 N.m. The hub has length of

A: Given data shaft dia = 30 mm length of hub = 50 mm allowable compressive stress = 120 MPa Required =…

Q: The coupled shafts shown are transmitting 270 hp at 600 rev/min. The shafts are connected by a…

Q: The motor drives a pump with a power of P = 34 kW. A steel tubular shaft with an outer diameter D =…

Q: Determine the maximum allowable torque T that may be applied.

Q: Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting 28…

Q: A motor supplies 173 hp at 650 rpm to flange A of the shaft. Gear B transfers 75 hp of power to…

Q: 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: H.W: Design a cast iron rigid type flange coupling to transmit 20 kW at 900 r.p.m. from an electric…

Q: naft has a diameter of 41mm. The PCD of the coupling bolts is 63mm. amter is 3mm, and the yield…

A: Given data-T=354Nm D=41mmPCD=63mm

Q: A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic…

A: Velocity Ratio = 4.6 : 1 From the data handbook for bush roller chain drive small sprocket teeth =…

Q: Mechanical design The maximum load in a rotating shaft is subjected to bending moment of 1 kN.m and…

A: Given data: The bending moment is M=1 kNm=106 Nmm The turning moment is T=1 kNm=106 Nmm The ultimate…

Concept explainers

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.

Question

A marine type flange coupling is used to transmit 3.75 MW at 150 r.p.m. The allowable shear stress in
the shaft and bolts may be taken as 50 MPa. Determine the shaft diameter and the diameter of the
bolts.
[Ans. 300 mm ; 56 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ steel bolts on a circle diameter of 228.60 mm. is subjected to a 950KN-mm torque.The shear stress developed in the outer circle of the flange bolt coupling is ___ MPa. 6.80 1.50 3.20 4.30 8.10
I need help with this question please. thank you
Problem 3.2, don’t do any other question, just problem 3.2
A flanged bolt coupling consists of six 2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 6000 psi in the steel or 9000 psi in the aluminum? Assume Gst = 12 × 106 psi and Gal = 4 x 106 psi.
1. The endurance limit for rotating shaft, if its ultimate strength Su=1600 Mpa is:
3. Find the power that can be safely transmitted by a flange type shaft coupling, if it has four equally spaced studs all at a radius of 50 mm from the shaft centre. The mean stud diameters are 12.5 mm, and each stud has a maximum safe working shear stress of 86 MPa. The shaft rotates at 3600 rpm.
Handwriting not allow please
• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft • Briefly describe which type of shaft is more effective. • See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page.
Q1. Design and draw a protective type of cast iron flange coupling for a steel shaft transmitting 'P' kW at 'N' r.p.m. and having an allowable shear stress of 40 MPa. The working stress in the bolts should not exceed 30 MPa. Assume that the same material is used for shaft and key and that the crushing stress is twice the value of its shear stress. The maximum torque is 25% greater than the full load torque. The shear stress for cast iron is 14 MPa.
A plain flange coupling is used by a 75 mm shaft to transmit 50 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm. Determine the bolt circle diameter if the shearing stress of the bolt is 25 MPa. A. 102.32 mm B. 202.64 mm C. 152.16 mm D. 252.78 mm
The 12B series chain was chosen to deliver 12 kW of power from the electric motor at 1400 rpm. The transmission ratio is 2. What is the diameter of the pitch driving circle and diven sprocket?
only Handwritten answer needed please. not typed