A main pipe of 150 mm diameter is branched into two pipes of 75 mm diameter each as shown. The branched pipes discharge water into atmosphere at a velocity of 8 m/s. The junction is in a horizontal plane and the friction is negligible. Determine the magnitude and direction of the resultant force. (Take p. = 10° kg/m3)

A main pipe of 150 mm diameter is branched into two pipes of 75 mm diameter each as shown. The branched pipes discharge water into atmosphere at a velocity of 8 m/s. The junction is in a horizontal plane and the friction is negligible. Determine the magnitude and direction of the resultant force. (Take p. = 10° kg/m3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 2 in tube schedule 40 flow 24 in 4 in tube schedule 40 - 6 in water h

A: given; lets take pressure at A=PAlets take pressure at B=PB⇒diameter at A (dA)=4in=0.1016m⇒diameter…

Q: A horizontal pipe is full of flowing water. At location A the velocity is 1.5 m/s and the…

A: The Pressure of the water at B is 133.43 kN/m3.Explanation:Given:v1 = Velocity at location A = 1.5…

Q: A woman is draining her fish tank by siphoning the water into an outdoor drain as shown in the…

A: The area of the base of the rectangular tank is A and the height is hTherefore, the volume of the…

Q: The diameter of a pipe carrying oil(s=0.92) changes gradually from 400 mm at A to 600 mm at B.…

A: Specific gravity of oil, SGo=0.92Diameter at A, DA=400 mm=0.4 mDiameter at B, DB=600 mm= 0.6…

Q: A siphon pipe of diameter 250 mm contracts to a diameter of 100 mm over a vertical distance of 5 m…

Q: There are 252,000m³/hr. of exhaust gas (MW=30) from the steam generator flo chimney with a velocity…

Q: = Q2: As shown in figure (2), when the water jet of diameter 25mm and Vj 30 m/sec., determine the…

Q: A vertical reducing bend carries 0.455 m^3/s of water at a pressure of 148kPa entering the bend at…

A: Given-Information:- Q= 0.455 m3/sp1 = 148 kpadA = 0.6 mdB = 0.3 mF = 35670 Nθ = 45° To-Determine:-…

Q: The system shown in the figure is used for painting in factory. The speed of the paint that enters…

A: Given data: a = 6 and b =2 Speed of the paint, u = 1(ab) = 1(12) = 12 m/s Density, ρ = 8(ab) = 84…

Q: The pump shown draws water from reservoir A at elevation 10 m and lifts it to reservoir B at…

Q: Water at a pressure of 300 kN/m flows through a horizontal pipe of 120 mm diameter with a velocity…

Q: ● Compute the time needed for the cylinder position to retract from the maximum position 1m to…

Q: Water enters a motor through a 500-mm-diameter pipe under a pressure of 15 kPa. It leaves through a…

Q: pump develops a head of 90 ft at 1750 rpm. Rated capacity is 1,000 gpm. Determine the size of the…

Q: Gate Vale-Half Open 4" Sch40 Globe Vale-Half Open 8 m 2" Sch40 2 m 2 m 10 m 2 m 5 m 10 m 450

A: Friction loss in the pipe is given by Darcy Weisbach formula hf=4fLV22gd f = friction factor L=…

Q: As seen in Figure below, the water passing through the flanged connection system is discharged to…

A: The flow entering section 1 is divided into section 2 and section 3. The law of conservation of mass…

Q: A tank is connected with cart by the rope A as shown in figure. When the water leaves the tank from…

A: Given:Px=pressure at surface=0Vx=velocity at free surface=0A=0.01 m2zx=2 m

Q: horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil (s.g.=0.88)…

A: Given:Diameter of the bigger pipe, D=300 mmDiameter of the smaller pipe, d=150 mmFlow rate, Q=0.127…

Q: 1a. Water flows into a tee fitting at a flow rate of 0.02 m3 /s. A pipe is connected to B. The…

Q: 4 mm drill holes in the large water tank causing water to flow out of the tank into a single…

A: Given:dia of hole, d=4 mmh=5 mangle of deflection, θ=180°

Q: QUESTION 2 A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant…

A: by problem,QB=QCQA=QB+QCQB=QC=QA/2f=0.0075DA=DB=50mmDC=?For A & B reservoir,ZA-ZB=fCADA X VA22g…

Q: 2. Three smooth rubber-lined fire hose each 60 m long and having 22 mm nozzle, are connected to a…

Q: ne of 50 mm diameter and 4.5 km length con t difference of water level is 12 m. A branch pipe…

Q: The velocity of the liquid flowing through the rusty iron pipe having a 150 mm diameter is 2.5 m/s.…

Q: Consider the wind tunnel shown below. The diameter at section 1 is 0.8 m and the diameter at section…

A: Given:Diameter at section 1, d1=0.8 mDiameter at section 2, d2=0.5 mSpecific gravity of manometer…

Q: Consider the bend shown in . The total mass of the bend and the water within it is 20 kg, with a…

Q: A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as…

Q: For the system shown below, calculate the vertical distance (in meters) between the surfaces of the…

Q: The shallow circular disk has a sharp-edged orifice at its center. A water jet of speed V strikes…

Q: Water is flowing at a rate of 25 gpm in a pipe and at one end of the pipe, the internal diameter is…

Q: A horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil…

Q: Water flows in a D = 36 mm diameter pipe as shown in the figure. Since Q = 60 m3 / h, and the…

A: As per given question we have calculate the resultant force on the elbow and the angle it makes with…

Q: Q//Determine the shaft power required for the pump to produce the flow shown in the figure . The…

A: Apply the Bernoulli’s equation between the tank surface and the nozzle. Write the expression of the…

Q: Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe…

Concept explainers

Fire safety

Fire safety is a new domain emerged in the early 90s to enable the design of buildings, structures, and infrastructure against destruction through fire. It also includes the provisions of building codes. This field is mostly associated with the design and efficient planning of a building, to reduce the destruction caused by fire. The branch of engineering that deals with it for the safety of the buildings from destruction of fire, is known as fire safety engineering.

Question

A main pipe of 150 mm diameter is branched
into two pipes of 75 mm diameter each as
shown. The branched pipes discharge water
into atmosphere at a velocity of 8 m/s. The
junction is in a horizontal plane and the friction
is negligible. Determine the magnitude and
8m/s
Ry
15°
150 mm
75 mm
30
75 mm
direction of the resultant force.
(Take p = 10° kg/m3)
8m/s

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Friction in pipe cause O 1. reduction in potential energy 2. Reduction in velocity 3. Reduction in pressure 4. Increase in pressure
Calculate the resultant force required in kN to hold a 90° elbow in place when attached to DN 150 Schedule 40 pipes carrying water at 0.1768 m3/s and 1 050 kPa. Neglect energy lost in the elbow. Do not include direction for the final answer! NB: Assume a water density of 1000 kg/m3 and use appropriate appendix to obtain necessary data. Hint: Draw a diagram showing the pipe system with the bent at the bottom right corner, water flowing from left to right then up to help you analyse the problem. Sign Conversion: North (+) and West (+)
Determine the volumetric efficiency of the reciprocating pump that has a boresize of 350mm and stroke of 400mm running at 360 rpm with slip of 10%
Water flows initially from tank A to B through a single pipeline which is 150 mm in diameter and 150 m in length, shown in the figure below. Further development requires that the flow rate is to be increased by 30 % by installing a second pipe in parallel, indicated by the dotted line and 82 m in length, running from A to c. The coefficient of friction for each pipe is 0,015. Determine the diameter of this new pipe. = ? L= 82 m 4 m 0 = 150 mm L= 80 m = 150 mm L = 70 m
Water at a pressure of 294 3 kN/m flows through a horizontal pipe of 100 mm diameter with a velocity of 2 m/s. If the diameter of the pipe gradually reduces to 50 mm, what is the axial force on the pipe assuming no loss of energy.
A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant difference of water level is 12 m. A branch pipe 1.25 km long and taken from a point distance of 1.5 km from reservoir A, leads to reservoir C whose water level is 15 m below that of reservoir A. Find the diameter of the branch pipe so that the flow into both the reservoirs is the same. Assume the coefficient of friction for each pipe, f = 0.0075, and neglect minor losses.
! Fast Please
On the head side of a hydraulic cylinder, the rod is 1/2 inch in diameter and the piston is 2 inches in diameter. Calculate the force applied while retracting the rod and the speed at which it moves if the operating pressure is 150 psi and the flow rate is 6.5 gpm. Answer is incomplete without units.
Water is pumped from the upper reservoir to the lower reservoir through the piping system shown. Determine the power required for the pump if the water flow rate is 60 kg/s. The fittings from pipe Di to pipe D2 and from pipe D2 to pipe D3 can be considered to be standard 90° elbows with velocity in pipe 2 for the friction loss. Data: h = 10 m, h2 = 3 m, L1 water viscosity = 1 cP = 103 kg/m-s, p= 1000 kg/m³. The pipe roughness is 0.05 mm. The pump efficiency is 75%. 50 m, L2 = 300 m, L3 = 2 m, D¡ = 0.2 m, D2= 0.5 m, D3 = 0.03 m, (1) D,, L, D2, L, Globe valve D3, L,
A3
A centrifugal pump develops a head of 16.8 m at 1500 rpm. Rated capacity is 0.015 m3/s. Determine the size of the impeller in mm if Øe=0.45.
6.7. Calculate the force exerted by the water on this orifice plate. Assume that water in the jet between orifice plate and vena contracta weighs 4.0 lb. 0.75 0.20 10' d