As seen in Figure below, the water passing through the flanged connection system is discharged to the atmosphere from the outlets no. 2 and no. 3. Calculate the force acting on the flange in the x-direction according to the figures given in the figure. (Ignore the effect of gravity and the friction of the fluid with the wall).

Q: 2 in tube schedule 40 flow 24 in 4 in tube schedule 40 - 6 in water h

A: given; lets take pressure at A=PAlets take pressure at B=PB⇒diameter at A (dA)=4in=0.1016m⇒diameter…

Q: Piston Pum 0.12 m saline 0.3 m

A: The work done in a piston cylinder assembly can be determined using the formula given below as-…

Q: A well has ¾ in of sucker rod and 21/2 in tubing with a specific gravity of the produced fluid of…

A:

Q: Q2: Find the value of Momentum thickness for the velocity distribution as given below - 2()-()

A: Given, uU=2(yδ)-(yδ)2

Q: The centrifugal pump shown in Figure Q2 is delivering water from Tank A to Tank B. The distance…

A: Given:L=8.5 mDischarge pipe diameter, D2=200 mm=0.2 mSuction pipe diameter, D1=300 mm=0.3 mDischarge…

Q: 5. The jets from both nozzles go out into the atmosphere at a speed of 35p/s. The liquid is water.…

A:

Q: Show the step by step solution. Thank you. 3. A pump draws water from reservoir A and lifts it to…

A:

Q: Problem 1: Consider the pipe system presented here. You have fluid flowing into a pipe at Point A.…

A: Step 1: THE VELOCITY AT THE POINT C AND D.   Step 2: THE PRESSURE AT THE POINT A

Q: = Q2: As shown in figure (2), when the water jet of diameter 25mm and Vj 30 m/sec., determine the…

A:

Q: The pressure at the suction of the pump reads 6 psi vacuum, while at the discharge is 43 psi. The…

A:

Q: then downward on the outside of the tube in a falling film. The tube radius is R. Determine: (a) The…

A:

Q: There is a flow of 8 kilograms per second of water into the pump, which then pumps the water to an…

A: Given data,  Water mass flow rate m= 8kg/s  Let density of water d= 1000 kg/m³  Pressure at output =…

Q: The system shown in the figure is used for painting in factory. The speed of the paint that enters…

A: Given data: a = 6 and b =2 Speed of the paint, u = 1(ab) = 1(12) = 12 m/s Density, ρ = 8(ab) = 84…

Q: The hydraulic jack shown below consists of a master cylinder with a diameter of 60mm and a lifting…

A: To find: The force at location B to lift the weight off the ground at location A. Given: The…

Q: In the figure the V-shaped pipe is filled with water, it is desired that the liquid remains in the…

A: The centrifugal force derives from the inertia of the moving body and is directed outwards from the…

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as…

A: For the solution refer below images.

Q: 3. In the following system, the flow rate of Q= 400 lt / s is transmitted from the A chamber to the…

A:

Q: derive the equation of the efficiency of the pump.

A: To derive: The equation of pump efficiency. Concept used: Pump: It is a device that transfers fluid…

Q: The pump shown draws water from reservoir A at elevation 10 m and lifts it to reservoir B at…

A:

Q: water which is to be drained completely. The exit pipe is exposed to the atmosphere. The distance…

A: given:hc=6mhB=1.2m

Q: The air flow through a jet engine is 30 kg/s and the fuel flow is 1 kg/s. The exhaust gases leave…

A: Given Data ma =30kg/s mf =1kg/s Ve =610m/s f=1.12x106 w

Q: A mechanism to spray water onto vehicles at an automated car wash is shown. Classify the four bar…

A:

Q: Water at a pressure of 300 kN/m flows through a horizontal pipe of 120 mm diameter with a velocity…

A:

Q: A valve for a pneumatic system has a hinge at point B. When you press down on the plate with your…

A: Given:To find:The absolute value of x for the position vector.The absolute value of y for the…

Q: f the velocity of water is 15 meters/sec and the pressure is 120kPa on the discharge side of the…

A: Given:At discharge side of the pump:V2=15 m/sP2=120 KPaAt suction side of the pump:V1=5 m/sP1=80 KPa…

Q: How much flow comes out of the cap end port of the cylinder when the cylinder retracts? Is that more…

A: A hydraulic cylinder is a hydraulic actuator that converts hydraulic energy into mechanical…

Q: ● Compute the time needed for the cylinder position to retract from the maximum position 1m to…

A:

Q: 3. Determine the value of Q₁, Q₂, Q₁, d₁, Q4 and v₁ when water flows through the pipes which are…

A:

Q: assume a flow of 1.7 m3/hr. the pressure readings are 0.1 bar at the bare pump and 0.3 at the…

A: assume a flow of 1.7 m3/hr. the pressure readings are 0.1 bar at the bare pump and 0.3 at the…

Q: b) To slow the boat very quickly a thrust reverser (or speed brake) is deployed (as shown in the…

A: Given data :-Velocity of V1=V2= VNozzle area (a) = a2Angle = 90°Find out :-  Thrust force on the…

Q: A fountain consists of a horizontal inlet pipe with a cross-sectional area, A1, which enters a block…

A:

Q: 4 mm drill holes in the large water tank causing water to flow out of the tank into a single…

A: Given:dia of hole, d=4 mmh=5 mangle of deflection, θ=180°

Q: 1 Determine the velocity at the inlet of the elbow 2 what is the velocity head inside the elbow 3…

A: given data, Dia = 4inch       =0.106mQ= 2000L/mm=2000×10-360 m3/secQ=0.034 m3/sec

Q: 1.The engine has a given capacity of 60kw, calculate the power requirement in a hydraulic system…

A:

Q: Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached…

A:

Q: Draw the right diagram for the problem. Show complete solution. Water at 60 F from a lake through…

A:

Q: What is the difference in potential energy per pound of mass of fluid at A and at B. STORAGE TANK…

A:

Q: :-in the figure shown find the pump power if the discharge of oil is 200L/sec and the relative…

A: