A long silicon pn junction photodiode has the following parameters at T =300 K: ni=1.5×1010 cm3, Na =1016 cm³, Nd =2×10!5 cm³, Dp= 10 cm³/s, Dn=25 cm²/s, TH0 = 5x10-7 s, Tp0=10-7 s, ɛr=11.7. The cross-sectional area of the diode is A=103 cm?. Assume that a reverse-biased voltage of 5 volts is applied and that a uniform generation rate for electron-hole pairs of GL=1021 cm3 s'l exists throughout the entire photodiode. The total steady-state photocurrent is equal to... 0.759 mA O 0.975 mA O 0.597 mA O 0.579 mA O

A long silicon pn junction photodiode has the following parameters at T =300 K: ni=1.5×1010 cm3, Na =1016 cm³, Nd =2×10!5 cm³, Dp= 10 cm³/s, Dn=25 cm²/s, TH0 = 5x10-7 s, Tp0=10-7 s, ɛr=11.7. The cross-sectional area of the diode is A=103 cm?. Assume that a reverse-biased voltage of 5 volts is applied and that a uniform generation rate for electron-hole pairs of GL=1021 cm3 s'l exists throughout the entire photodiode. The total steady-state photocurrent is equal to... 0.759 mA O 0.975 mA O 0.597 mA O 0.579 mA O

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The diode from the following characteristic curve in Figure 1 was changed to zenerdiode. Determine: the function of zener diode in reverse biased. Briefly explain the differencebetween conventional diode and zener diode.
In a Si diode, the junction area is 0.25 mm2 and the doping density of the n-type region is ND = 1017 / cm3. ; Additive density of p-type region NA = 1015 /cm3. ni = 1,5 1010 /cm3, q = 1,602 10-19 C, VT = 25mV, r = 12, o = 8,85 10-14 F/cm, μn =1350 cm2/Vs, μp = 480 cm2/Vs, τn = τp = 1 At room temperature, a. Find the densities of minority and majority carriers in both regions b. What is the potential wall height?
Determine the noise current for a diode with a forward bias of 1mA over a 100 kHz bandwidth. If the diode is in a circuit with 5002 series resistance, calculate the total output noise voltage at 27°c. (from miller: In = 0.00566µA, total noise voltage = 0.154 µVrms) %3D
In the given circuit, D1 is Silicon diode and D2 is a zener diode with breakdown voltage of 6.8V. Assuming RC time constant of circuit >> T. Find the Maximum and Minimum value of the output waveform.
in a compound semiconductor intrinsic level is found to be 0.0003ev below the mid gap at 300l what is the ratio of the electron effective mass to the hole mass
The diode current at 25°C for a silicon diode with Is= 55 nA an applied forward bias of 0.8 V is -----. Note: use K=11600/2 0.543 A O 0.2 A 0.743 A 0.318 A
Light-emitting diodes (LEDs) are diodes made with III-V compound semiconductor materials such as aluminum gallium arsenide (AlGaAs), aluminum indium gallium phosphide (AllnGaP) or indium gallium nitride (InGaN), instead of silicon. The LEDs emit light when the device is operated under forward bias. LEDs of different colors have different turn-on voltages VD(on). For example: Color VD(on) Red ~ 1.6 V Yellow ~ 1.7 V (a) Model these five LEDs with a simplified piecewise linear model. (b) A rule of thumb is that it takes about 1 mA of current to "light" an LED while~ 10 mA is needed for it to appear bright. Use the piecewise linear model for the LEDs, for the over-voltage indicator circuit to the right, find the values of Vin which will cause D₁ or D₂ to light (i.e. when ID1 or ID2 exceeds 1 mA). Green ~ 1.8 V Blue ~ 2.8 V loks o mu Vin Red LED Red LED White ~ 3.8 V + lov 21 D₁ D2 -10V o t Vout 오
6:39 Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=5 V and V2=9 V. www Vin Vout Maximum voltage of output waveform Minimum voltage of output waveform
Find values of the intrinsic carrier concentration ni for silicon at -55°C. 1.5 x 1010 carriers/cm3 O 5 x 1010 carriers/cm3 2.7 x 106 carriers/cm2 2.7 x 106 carriers/cm3
Q.2 Te diodes m the Cir Cuit of 6iG. below are icdead , Drow the Tran sfer characteristic for 2ovSVi s 2ov ? Di Ri R3 lov
Find Idc, Vdc and the capacitance that will force the Vr(pp) to 3mV. Draw the output waveform across the capacitor. Fin=60Hz.
Show the solution