5. Determine the output waveform of the network for the input indicated (USE 1ST APPROXIMATION) * 1uf Vin 12 V Vin 100k2 7V -12 V 1. Diode is ON state at the. half eycle 1pt Vo=, 1pt 2. Capacitor charges. Ve = 1pt 3. Diode is OFF state when Vc=. 1pt 4. Determination of Vo Vo =. (@ + half cycle) 1pt Vo =. (@ - half cycle) 1pt 5. Output Waveform 4pts

5. Determine the output waveform of the network for the input indicated (USE 1ST APPROXIMATION) * 1uf Vin 12 V Vin 100k2 7V -12 V 1. Diode is ON state at the. half eycle 1pt Vo=, 1pt 2. Capacitor charges. Ve = 1pt 3. Diode is OFF state when Vc=. 1pt 4. Determination of Vo Vo =. (@ + half cycle) 1pt Vo =. (@ - half cycle) 1pt 5. Output Waveform 4pts

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
Find output waveform. vo Consider the ideal R diode.
For the circuit shown below, sketch to scale the output V waveform and draw the transfer characteristic (V versus Vi), Assume the diodes are ideal.
In reference to the output waveform below and using ideal diode model: Vout +7.5V -3.5V a. Analyze the behavior of the circuit and fill up the table below. Vin Diode state Vout (FB or RB) +6V OV -3V -6V b. Draw the clipper circuit that will produce the given output waveform.
Consider the circuit in the figure below 4:1 120 V rms ooooo gll reelee D₁ L a. What type of circuit is this? b. What is the total peak secondary voltage? D₂ c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? RL 1.0 ΚΩ
For the circuit in the figure, let V input = 8V, Ri = 12ohms, RL = 10ohms, and VZ = 3.3V. Determine the voltages and currents of the resistors and the current of the zener diode.
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode
Determine the diode current (in Ampere) at 70°C for a silicon diode with reverse saturation current 70 nanoAmpere and an applied forward bias of 0.8 volts. The constant k value is: The Temperature (in Kelvin) is: The Diode current (in Ampere) is:
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
What voltage is boosted at the output of a multiplier. a) average b) rms c) peak d) instantaneous Which assumption is not used in the analysis of multipliers? a) a capacitor will not discharge b) start with the cycle of the source that will forward bias the nearest diode c) the output will always be multiplied d) a single diode is forward biased at a time A voltage multiplier a) multiplies the output voltage b) has very high voltage and low current c) can employ inductors d) may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations at a) the input and output b) the load c) source d) in the environment Between a lower percent regulation and a higher one, which is better? a) lower b) higher
Consider diode circuit shown below with Vcc=5V and V₂ = 3V. U₁A HH +V₂ ū The peak inverse voltage on the diode is close to V₁ V. A Vo
The Zener diode shown below, is specified to have Vz-20V at Izr, IzK = 0.1 mA, IzT =17 mA, and r, = 14 2. Voc = 30V. 1) Replace the Zener diode with its Model. 2) Find the current I with no Load. 3) Find Vo with no Load when VCC = 30V. 4) Find R1 Min. r30V 2000 Vz = 20V %3D 68-V zener