A line measured in the field and found to be 1,219.00 m, with a steel tape with length of 50m, and weight of 0.70kg. The cross-sectional area of the tape is 0.03cm^2, and was standardized at a temperature of 20°C under a tension of 5kg. Find the correction of the line due to tension, temperature and sag. Find the corrected length of the line, if the distance measured in the field under tension force of 10kg and at a temperature of 35°C. The modulus of elasticity, E, is 2.10 x 10^7 kg/cm^2. K = 0.0000116 m/m°C.

A line measured in the field and found to be 1,219.00 m, with a steel tape with length of 50m, and weight of 0.70kg. The cross-sectional area of the tape is 0.03cm^2, and was standardized at a temperature of 20°C under a tension of 5kg. Find the correction of the line due to tension, temperature and sag. Find the corrected length of the line, if the distance measured in the field under tension force of 10kg and at a temperature of 35°C. The modulus of elasticity, E, is 2.10 x 10^7 kg/cm^2. K = 0.0000116 m/m°C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. Two exactly similar wires, one of steel and the other of copper, are stretched by equal force. If the total elongation is 2 cm, find how much is each wire elongated. Y for steel is 2 x 10 N/m² and for copper is 12 x 10 N/m.
A distance of 412.3 m was measured using a steel tape with a nominal length of 30 m, a cross-sectional area a = 0.000004 and a support gap of its entire length under a tensile force of ps = 5.5 kg, temperature 20 °, use the tape to measure the height difference between their ends (20) m (d = 20) The tape was supported with full strength, the height = 500 m above sea level, the temperature during the measurement in it = 12°, the tensile force applied during the measurement was p = 8 kg, the real length of the tape = 30.2 m, the coefficient of thermal expansion was α = 000006 and the modulus of elasticity E=203.23 × 10 ^6 kg /m^2 Determine the correct
NOTE: The standard pull of the tape is 5kg while the team pulled only at 4kg The field temperature is 300 while the standard temp of the tape is 200 The cross sectional area of the tape is 0.05cm2. The coefficient of linear expansion is 0.000011610C and the modulus of elasticity of steel is given to be 2.0 x 106 kg/cm. The tape used here is a 50m steel tape. Determine the actual length of each lines
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. 50kN A 20 купи RI B 2M X 30KN/M TITT. 4m 20 km. ITTJ 2m + <
Please show a hand written solution and the exact fbd for the solution. Thank you!
A pump is driven from an engine crank-shaft by the mechanism as shown in Figure . The pump piston shown at F is 250 mm in diameter and the crank speed is 100 r.p.m. The dimensions of various links are as follows: OA = 150 mm ; AB mm; DE = 500 mm. Determine for the position shown: 1. The velocity of the cross-head E, 2. The rubbing velocity of the pins A and B which are 50 mm diameter. 3.The acceleration of the cross-head E. 45 A 300 600 mm ; BC = 350 mm ; CD = 150 %3D 450 100 1111 All dimensions in mm.
The 100X200 mm cross section of the simple support beam given in the figure was obtained by gluing four pieces of wood of 50X100 mm to each other as shown in the figure. The shear safety stress for the adhesive is 0.35 MPa and the bending safety stress for wood is 11 MPa. Calculate the maximum force P that can be applied to a beam with a span of 3 m. The load is applied at a distance of 1 m from the left support. Include the weight of the beam itself in the process and take 5.5 kN / m3 for the weight of the wood. Draw the cross section diagrams (shear force and bending moment). Show how you draw using the separation technique.
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. SOLVE IN 2 DECIMAL PLACES. BOX THE FINAL ANSWERS.
Read the question carefully and give me right solution according to the question
A line was found out to be 2865.35 m long when measured with a 30-m tape under a steady pull of 6.5 kg at a mean temperature of 30 degC. Determine the correct length of the line if the tape used is of standard length at 20 degC under a pull of 5.5 kg. Assume that the cross-sectional area of the tape is 0.025 cm², elastic modulus of tape is 2.10 x 106 kg/cm? and coefficient of linear expansion of steel is 11.6 x 106 per degC.
A slender homogeneous wire of uniform cross-section is bent into the shape as shown. Determine the coordinates of its center gravity with respsect to the reference X and Y axes