A 30 m tape weighing 1.150 kg is of the standard length under a pull of 5.000 kg supported for a full length. The tape was used in measurin

Q: A full forming P= 50 kN axial force acts on the part shaped by the machining method made of xCy…

A:

Q: A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and…

A: The load is P=10 kN. The length is l=3 m. The cross-sectional area is A=1000 mm2. The modulus of…

Q: Using the node method, determine the force on the GL element and indicate whether it is in tension…

A:

Q: A cube of a material with a yield strength of 100x10° N/m?is subjectedtothe loads shown onthe right.…

A: The maximum shear stress is generally the maximum concentrated shear force in a small area. In…

Q: O A rectangular strip 50×15mm deep of brass is placed on top of another strip 50×15mm deep of steel…

A:

Q: The temperature was 10 oC during the measurement, and the tape was supported on both ends. The tape…

A:

Q: 4. Find the lightest S-shape for the beam shown if the working stress in bending is 175 MPa. What is…

A: The given figure of beam is shown below:

Q: ) Determine the normal stress at point A. b) Determine the normal stress at point B

A:

Q: The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if…

A: For small angles.

Q: For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the…

A:

Q: OV ko T | B P · C a b c F D + W 11¹ h

A:

Q: A RIGID BAR "AB" ATTACHED TO TWO VERMCAL RODS IS HORIZONTAL BE FORE LOAD "P" IS APPLIED. DETERMINE…

A: Given Data  Length of steel = 2.4m = 2400 mm  Length of aluminum = 1.4m = 1400 mm Modulus of…

Q: 30 K 15 20 15 130 20 Ratio of major principal stress to minor principal stress up to two decimal…

A:

Q: The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in…

A:

Q: Link AB is to be made of a steel for which the normal stress is 310 MPa. Determine the…

A:

Q: A 100m steel tape is used to measure the distance of the line and found to be 1529.28m long. During…

A:

Q: The beam below has a fixed support at A and a roller support at B. It is subject to transverse…

A:

Q: Solve

A:

Q: A tapered circular rod of diameter varying from 20 mm to 10 mm is connected to another uniform…

A: A tapered circular rod of diameter varying from 20 mm to 10 mm,Uniform circular rod of diameter 10…

Q: Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical…

A:

Q: A 30 m tape weighing 1.150 kg is of the standard length under a pull of 5.000 kg supported for a…

A: We just need to find Sag correction and should be added with measured line to get correct length.…

Q: A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor…

A:

Q: Part 8

A: Data given Load P = 250 kN Modulus of Elasticity of Steel, Es = 200 ×106 kN/m2 Modulus of…

Q: Determine the steel area required for the section shown: If Mu = 1500 KN. M 70

A:

Q: Pu Pu Pu Pu Pu Pu Pu * (a: 10' - F L K J I H * (a 10 - RI Ru 8@10'=80'

A: We can solve the truss by 2 methods  Method of joints  Method of sections    Negative sign means…

Q: Four-25-mm-diameter rivets with an axial load of T= 75 kN distributed equally as shown. The…

A:

Q: For the beam shown below, Find the bending stress at point A. 50 kN 1.3 m. 120 a 22 22 20 3 m 3 m

A: Given that:

Q: y 150 mm 150 mm B 400 mm 600 mm A

A:

Q: What pull in kilogram (normal tension) is required in order that the effect of sag will be…

A: Surveying through tapes can be quiet erroneous. Several errors like error due to slope,…

Q: blem 6.107 - Copy me beam is subjected to the internal moment of M = 2.9 N-m. (Figure 1) ure 50 mm…

A:

Q: An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross…

A:

Q: H B A An aluminum rod AB of diameter 3.4 inches is connected to a lever of length L = 5.8 feet.…

A:

Q: Compute the moment about x-axis of thin plate with constant density 8(x, y) = 5, bounded below by…

A: mx = 3.93

Q: Determine the proportional shear stress for a material that has a modulus of rigidity of 30 GPa and…

A: Given data : Shear  strain=0.0001Modulus of rigidity (G)=30 GPa

Q: An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: stresses on an element is given as followschange in length of diagonal BD=?

Q: Steel rod Steel rod A = 900 sq. mm A = 900 2 m sq. mm Copper A = 1200 2 m ww bs A B 1m 1 m

A:

Q: A simply supported wooden I beam AB (shown below) is loaded by the distributed force q = 1.9 kN/m.…

A: Given data:

Q: A flat steel bar, 29 mm wide by 5 mm thick and 1.5 m long, is bent by couples applied at the ends so…

A:

Q: The bro

A: Calculate the restrained elongation. Then using the formula for elongation the compressive load can…

Q: 2. Given a rectangular plate which is deformed as shown by the broken line. Determine the average…

A:

Q: Hiwe A bar with constant ss-section area(Aland unit weight () is subjected to axial force ce) in…

A:

Q: Q2: Neglecting the effect of fillets and of stress concentrations, determine the smallest…

A: Given: Length of rods  Allowable shear stress  Loadings  To find:  Diameter of rods  Notations :  r…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.