A large reservoir supplies water for a community. A portion of the water supply system is shown. Water is pumped from the reservoir to a large storage tank before being sent on to the water treatment facility. The system is designed to provide 1310 L/s of water at 20°C. From B to C the system consists of a square-edged entrance, 760 m of pipe, three gate valves, four 45° elbows, and two 90° elbows. Gage pressure at C is 197 kPa. The system between F and G contains 760 m of pipe, two flanged open gate valves, and four 90° regular flanged elbows. All pipe is 508 mm diameter, cast iron. Calculate the average velocity of water in the pipe, the gage pressure at section F, and the power input to the pump (its efficiency is 80 percent). P8.169 B I = 174 m 152 m Pump z = 104 m z=91 m. C

A large reservoir supplies water for a community. A portion of the water supply system is shown. Water is pumped from the reservoir to a large storage tank before being sent on to the water treatment facility. The system is designed to provide 1310 L/s of water at 20°C. From B to C the system consists of a square-edged entrance, 760 m of pipe, three gate valves, four 45° elbows, and two 90° elbows. Gage pressure at C is 197 kPa. The system between F and G contains 760 m of pipe, two flanged open gate valves, and four 90° regular flanged elbows. All pipe is 508 mm diameter, cast iron. Calculate the average velocity of water in the pipe, the gage pressure at section F, and the power input to the pump (its efficiency is 80 percent). P8.169 B I = 174 m 152 m Pump z = 104 m z=91 m. C

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

What will result from too little EGR flow? And what can cause a reduction in the flow?
Please include a diagram.A pump supplies water at a flow rate of 4ft3/s from an open reservoir through a horizontal 8-in sched 40 pipe. The head loss from the reservoir to the suction of the pump is 2 ft-lbf/lbm, and the discharge is at 90 psig into a 6-in sched 80 pipe. The pump has an efficiency of 65% answer the following:a.) The head that must be delivered by the pump to the water is ________ or energy developed by the pump or output energy of the pumpb.) input energy to the pumpc.) Rated power of the pump in kW
1. As a junior city engineer of a municipality, you are tasked to design the specifications of the pump with 3650 cu.m/day. The water source in the municipality is from an open reservoir and will supply to a pressure tank that will distribute to the municipality. open 4l Pressure reservoir Tank 70 m 15 m Pump Determine the following specifications of the pump and piping system (assume fluid stagnation at the pump). Velocity head at pt.1 to 2 if the diameter of the pipe is a.) 200 mm b.) Suction pressure of the pump in kPa (Pressure at pt. 2). c.) Velocíty head at pt.3 to 4 if the diameter of the pipe is 150 mm d.) Discharge pressure of the pump in kPa (Pressure at pt. 4). Assume atmospheric pressure at the pump. If an air vent is installed at the pipe just right before the pressure tank with diameter of 20 mm, what is the velocity of discharge in m/s? The height of the pressure tank is 12 m, what is the flowrate in cu.m/hr at pt.5 if the diameter of the pipe is 150 mm? e.) f.)
From THERMOFLUIDS, M. MASSOUD Please hep me solve this problem i will really appreciate it
None
4. to convert the kinetic energy of water into the mechanical shaft energy. Water enters the turbine, at the inlet, with the velocity Vin = 40m/s and the mass flow rate m=1,000kg/s. Water exits the Vi,z40ms turbine with a negligible velocity, say, Vout = 0 m/s.The efficiency of m - loooly/s Figure on the right shows a hydraulic turbine designed HzO HzO the turbine is 75 %. Potential energy and flow work can be ignored. 4а. Please calculate the specific kinetic energy of water entering the turbine ( ɛr or ke; in J/kg). 4b. Please calculate the rate of total kinetic energy of the water flow ( É̟ or KĖ ; in J/s or W) 4с. Please determine the mechanical power output of this turbine (Wou; in W or kW). 4d. Please determine how much mechanical energy would this turbine generate during an hour
P: 50,000 ii. 2m Pa 50mm Pump VALVE P= 175,000 25mm Pa TURBINE P= 40,000 Pa с 25MM The diagram above shows the set up for a pump and water turbine unit at a power generation company in Point Lisas. i. The water has a temperature of 25°C and the head losses accumulated by the valve and fittings is 2 N.m/N between points A and B. If the flow rate is 0.02m³/s and the pump is 75% efficient, determine the power put into the pump. Determine the energy removed by the turbine and use it to determine the mechanical efficiency of the turbine given that 2450W of power is outputted from the turbine.
The initial condition of air in an air compressor is 100 Kpa and 25 degrees Celcius and discharges air at 725 Kpa. The bore and stroke are 276 mm and 186 mm respectively with 3 % clearance runningat 6 rev/sec.1.1 Illustrate the PV diagram 1.2 Discuss the processes in PV diagram 1.3 Solve the volumetric effieciency
The efficiency at the best operating point is: Head (ft) O-4% O 23% O 28% 5% 85.00 80.00 75.00 70.00 65.00 60.00 55.00 50.00 45.00 40.00 35.00 30.00 25.00 20.00 15.00 10.00 Pump Curve System Curve Effe. Poly. (Pump Curve Poly. (System Curve) Operating Point Chart 20 30 40 Q (gpm) 50 60 70 35% 30% 25% 20% 15% 10% 5% 0% -5% -10% -15% -20% -25%
ANSWER ASAP PLS
4. Water is circulated from a large tank, through a filter, and back to the tank. The required water flowrate is 2 m?/s. Determine the power of pump (Watts). KL exit 1.0 KL elbow = 1.5 KL valve 6.0 KL ent = 0.8 %3D KL fiter = 12.0 3 cm-dia. Filter- pipe with e/D = 0.01 Pump 0.1 0.09 Wholly turbulent flow 0.08 0.07 0.05 0.04 0.06 0.03 0.05 0.02 0.015 0.04 0.01 0.008 0.006 0.03 0.004 0.025 0.002 0.02 0.001 0.0008 0.0006 Laminar flaw 0.0004 0.015 Smooth 0.0002 Transition range 0.0001 0.00005 0.01 0.009 0.008 0.00001 2110') 21104) 4 6 B 2110) 6 8 2(10 6 8 2(10) 6 8 4 6 8 4. 4 4 10 10 10 10 107 Re a PVD
Water is being delivered by a pump at 400 LPM through a 3 in ID pipe. A 3 x 2 reducer was fitted to increase the velocity. What will be the difference in the average velocity, in m/s, in the 3 in and 2 in ID pipe? 3.65 a. 1.83 b. 2.42 C. d. Answer is not among the choices