liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to supply water to the tank at the rate of 245 1/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the

liquid is pumped from a ground level reservoir to an overhead tank through a 5 cm ID pipe as shown in Fig. (1): i. What pressure developed by the pump to supply water to the tank at the rate of 245 1/min? ii. What is the power required for the pump, if the pump is only 62% efficient? iii. Calculate the available NPSH. If the

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. The discharge pipe of a pump is 400 mm in diameter delivers 0.5 m3/sec of water to a building which maintains a pressure of 100 Kpa at a height of 30 m, what power must be furnished by the pump?
Q9: Find the specific speed and power consumption for pump having the following properties: (Q=0.1 m3/s), (speed=725 r.p.m) and (head =15 m).
A fully-filled open storage tower of height 32 m and diameter 3.0m supplies water to a house. A horizontal pipe at the base of the tower has a diameter of 2.54cm. To satisfy the needs of the home, the supply pipe must be able to deliver water at a rate of 0.67 gal/s. a. If water were flowing at the maximum rate, what would be the pressure in the horizontal pipe?b. A smaller pipe, of diameter 1.27 cm supplies the second floor of the house, a distance of 7.2 m above the ground level. What are the flow speed and water pressure in this pipe?
I am having trouble with this problem.
As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical lift of . The inlet to the pump is just below the water surface and the discharge is to the atmosphere through a DN50 schedule 40 steel pipe. The energy loss . (1) Calculate velocity at the exit of point 2__________m/s
1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
QUESTION 3 A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when operating in the system sketched in Fig. 3. An energy loss of 2.3 m occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency. A 27 kba 12 m
In a hydraulic pump, the theoretical flow rate delivered is 217 liters/min with its volumetric efficiency is 97.5%, Then find the actual flow rate in liters per second.
1. Water from a reservoir passes over a dam through a turbine and discharges from a 60-cm ID pipe at a point 40 m below the reservoir surface. The turbine delivers 1 MW. a. Draw the system and write the relevant form of the mechanical energy balance. b. Calculate the required flow rate of water in m3/min if friction is neglected. (Note: The equation you will solve in this problem has multiple roots. Find a solution that is physically relevant.) c. If friction were included, would a higher or lower flow rate be required?
In a hydraulic pump, the theoretical flow rate delivered is 203 liters/min with its volumetric efficiency is 83.5%, Then find the actual flow rate in liters per second
Calculate the NPSHA in ft for the following configuration of a pumping system. Pv=924.8Kpaa ... Vessel Pressure = 134.6 psia Minimum Operable Liquid Level 15 ft Water, 350F Datum Suction Line Losses = 5 ft (1.52m)