(a) -L2

Q: A cone clutch is mounted on a shaft which transmits power at 200 rpm. The small diameter of the cone…

A:

Q: A flat collar bearing has an external diameter which is 1.6 times the intenal diameter. The…

A:

Q: (7) The cylinder head of a 10"x18" refrigerant compressor is attached by 10 stud bolts made of SAE…

A: Given: Let us consider the given, Cylinder pressure=350 psi Area of the cylinder head,A=10ιι×18ιι…

Q: Your task is to design a full journal bearing to support the crankshaft of an engine. The crankshaft…

A: Given Data:- N=6000 rpm T1=130F d=2.5in L=1.5in f=0.04

Q: What is the proportion of the alteration in length for Spring A to Spring B, supposing  that both…

A: This question is based on the concept of springs.

Q: A square threaded bolt of mean diameter 24 mm and pitch 5 mm is tightened by screwing a nut whose…

A:

Q: 3. The safe working stress of a belt is equal to the tight side tension over the product of the…

A:

Q: pulley, 610 mm. in diameter, transmits 40 kW at 500 rpm. The arc of contact between the belt and the…

A:

Q: A car jack uses a single square-thread screw to raise a known load. The major diameter and pitch of…

A: Answer: (a) The efficiency of the jack for raising the load: 8.9206 % (b) The power required to…

Q: The inner and outer radii of a hollow steel shaft are 50 mm and 100 mm, respectively. The hub of a…

A: Given Inner radii of hollow shaft ri=50 mm Outer radii of hollow shaft ro=100 mm Maximum allowable…

Q: Problem 208 A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and…

A:

Q: The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade…

A:

Q: A cylinder of a four stroke diesel engine has the following specifications: Brake power = 5 kW…

A:

Q: Whqt are Rigid Bodies? Give at least 5 examples with description.

A: Given Data : Rigid bodies

Q: A 125 kg wheel with a radius of 2.50 m is being pulled up an incline by a 550 kg horse. There is a…

A:

Q: Problem 208 A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and…

A: Given Data: Thickness t=10 mm Wide b=80 mm Inside Diameter di=1500 mm After heating final diameter…

Q: The following data is refers to a screw jack. The vertical load on the screw320kN Force applied at…

A: Answer: (a) The force on the lever end while raising the load is 134.82625 N. (b) The efficiency of…

Q: (7) A clutch system is to be designed to transmit 800 ft-lb of torque. A multi-plate clutch in an…

A: Given:The torque transmitted by the clutch system, The maximum diameter of the outer disk, The…

Q: An automotive plate clutch consists of two pairs of contacting surfaces with asbestos friction…

A: Write the given data.

Q: The cylinder of a four-stroke diesel engine has the following specifications: Brake power Speed =…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Blocks in (Figure 1) A and B have a mass of 5 kg and 16 kg, respectively. Figure 400 mm 300 mm B DO…

A: Given:The mass of block A is .The mass of block B is .Consider free body diagram of block A and…

Q: A connecting rod for an I.C. engine running at 1800 r.p.m. and developing a maximum pressure of 3.15…

A: Solution. Given : N = 1800 rpm; p = 3.15 MPa; D = 100 mm; mR = 2.25 kg; l = 380 mm = 0.38 m; Stroke…

Q: A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a…

A: Given: n=6 T = 1100 Nm N = 2100 rpm b = 123 mm s= 127 mm

Q: A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a…

A: Given data: Number of cylinder in engine (n)=6 Compression ration (r)=9 Speed (N)=2100 rpm Torque…

Q: A cone clutch is to transmit 7.5 kW at 900 rpm. The cone has a face angle of 12o. The width of the…

A:

Q: A car engine has its rated output of 120 kW. The maxmum torque developed is 110 Nm. The clutch used…

A: GIVEN DATA -

Q: A clamp coupling is to transmit a power of 13 kW to a shaft rotating at a speed of 511 rpm.…

A:

Q: The value of RSS (in mm),

A: Given;  Solid steel disc of initial radius, → RIN=200 mm→ Initial height, HIN=50mm→Attains a height…

Q: The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12…

A:

Q: Expected life of bearings in millions of revolutions                       ii) Design equivalent…

A: For solution refer below images.

Q: A 600 mm steel pulley transmits 50 kW at 900 rpm. The arc of contact between the belt and pulley is…

A:

Q: A pullev 615 mm in diameter transmits 40 kW at 630 rpm The arc of contact between the belt and the…

A:

Q: A pulley 590 mm in diameter transmits 50 kW at 520 rpm. The arc of contact between the belt and…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.