(7) The cylinder head of a 10"x18" refrigerant compressor is attached by 10 stud bolts made of SAE grade 5. The maximum cylinder pressure is 350psi. (a) What size of bolt is to be used? (b) What approximate tightening torque should be applied to induce a tightening stress of 0.9 time of the proof stress?

Q: drive; inner race stationary. Decide upon a deep groove ball bearing, giving its significant…

A:

Q: Required information For a bolted assembly with 19 bolts, the stiffness of each bolt is kh= 1.0…

A:

Q: A gear train is composed of four helical gears with the three shaft axes in a single plane, as shown…

A:

Q: A 02-series single-row deep-groove ball bearing is to be selected from Table 11-2 for the…

A:

Q: A 1/2-in-dia UNC, class 2 bolt with rolled threads is preloaded to 80% of its proof strength when…

A: Part (A): Write the given data. d=0.5 inL=3 inPmax=1000 lb

Q: The bolts used to mount an engine on an industrial machine must each carry a static tensile load of…

A: For the bolt material, SAE grade 5 UNC, the yield strength is generally,

Q: For a bolted assembly with eight bolts, the stiffness of each bolt is K,=1.0 MN/mm and the stiffness…

A:

Q: A journal bearing has a shaft diameter of 70.00 mm with a unilateral tolerance of-0.02 mm. The…

A:

Q: The power transmitted by a 3 1⁄4 - in. shaft is received through a sprocket, made of as cast nodular…

A: A shaft is a spinning machine element with a circular cross section that is used to convey power…

Q: The design of journal bearings usually involves two suitable combinations of variables: variables…

A: given; shaft journal diameter(d)=27mmtolerance=20.01mmbushing bore diameter (D)=27.04load(w)=1.03KN…

Q: What size UNF bolt made from SAE grade 5 steel is needed to carry a static tensile load of 3000lb…

A:

Q: Define the term Shaft Design?

A: Given Shaft design To find Definition

Q: 12. A cylinder with a bore diameter of 100 mm and a rod diameter of a 40 mm is to be used in a…

A:

Q: A single deep grove ball bearing series 3, the outer ring rotates at 1500 rpm with little shock…

A: Given, Bore diameter of ball bearing,d=45mmRadial load,Fr=1890lb=8407NAxial…

Q: How the sec (alpha) value is measured 29/2? Can you please describe the circled line in…

A: Unfortunately, I cannot access the circled line in the document you mentioned as I cannot directly…

Q: RB&W11 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4…

A: To findthe torque is necessary to establish the desired preload.The turn of the nut.Givenpreload,…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.