A 600 mm steel pulley transmits 50 kW at 900 rpm. The arc of contact between the belt and pulley is 144 degrees, the coefficient of friction between belt and pulley is 0.3 and the safe working stress of the belt is 2750 kPa. Find the width of the belt used if the thickness is equal to 12 mm.

Q: The 60° V-belt of a machine is pass around the pulley A of a motor and over a pulley B as shown in…

A:

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: 3. A V-belt drives a pulley at a speed of 1440 m/min. The coefficient of friction between belt and…

A: Given data: - The speed of the belt is v = 1440 m/min. The friction coefficient between belt and…

Q: 300 rpm. The coefficient of friction between the belt and the pulley is 0.26, angle c lap 160° and…

A:

Q: If the coefficient of friction is 0.25, calculate the tension T in the cable to raise the load. Find…

A: Given:Coefficient of friction, μ=0.25mass, m=800 kg

Q: The larger and smaller pulleys of a chain block has 31 and 29 recesses respectively. If the…

A:

Q: (a) A body of weight 55 N is placed on a rough horizontal plane. To just move the body on the…

A:

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A:

Q: An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the…

A:

Q: 20 kg ladder AB up a wall by applying the horizontal force P (Figure 4). Determine the height, h…

A:

Q: B) A body is pulled by a rope which passes 3 times round a power-driven capstan 600 mm diameter,…

A:

Q: Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The…

A:

Q: the bolt is 60 mm. with bolt The friction coefficient between the nut and bolt and the handle is…

A:

Q: Determine the force T that will produce impending motion upward of the 500-lb weight in Figure…

A:

Q: Find the value of coefficient friction if friction force is 222 N and Normal force is 1000 N

A: Given data : Friction force=f Normal force=F'   Required : Coefficient of friction

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

A:

Q: A flat belt is wrapped around a Ø3.00-inch pulley for 217°. The loose side belt tension is 282 lb…

A:

Q: Two parallel shafts whose centre lines are ‘5’ m apart, are connected by an open belt drive. The…

A: C=5 mD=3 md=3 mTmax=4 KNμ=0.3N=700 rpmVelocity of belt, V=π*d*N60V=π*3*70060=109.95 m/s

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: For the figure shown, two blocks are connected by a uniform solid rod attached to each block with…

A: Given data :- coefficient of friction (μ)=0.65 weight of block B (WB) =2700N To find:- Minimum…

Q: Find the coefficient of friction if friction force is 723N Normal force is 823 N

A: Given data : Normal force=N Friction force=F   Required : Coefficient of friction

Q: A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is…

A:

Q: Find Coefficient of friction f = 233N N'= 430N

A:

Q: Two pulleys rotating in opposite direction has the following properties: D1 = 430 mm, D2 = 180 mm,…

A: The given information in the problem is listed in the following attached image:

Q: A pulley consists of a 120-mm-diameter wheel that fits loosely over an 18-mm-diameter shaft as shown…

A: Given: M=2.5 kgWeight of pulley is 5 N.r1=182=9 mmr2=1202=60 mm The free-body diagram of the pulley…

Q: The hand brake of Fig. is used to control the rotation of a drum. The coefficient of friction…

A: Given: The torque on the drum, T =  5 ft.lb The coefficient of friction between belt and drum, μ =…

Q: A pulley system uses four v-section belts each with a cross-sectional area of 700mm 2, an included…

A: The maximum force (tension) in the belt can be given as -  T1 = 3×Centrifugal force500 =…

Q: A flat belt is required to transmit 35 kw from a pulley of 1.5 m effective diameter running at 300…

A: Given:P=35 KWd=1.5 mN=300 rpmθ=1124*2πμ=0.3t=10 mm

Q: A leather belt of thickness 6 mm and width 80 mm connects two pulleys of 500 mm diameter and 900 mm…

A:

Q: Given: Q=14,361.60gpm L=1000ft D=2ft hf=12.58ft. Determine the friction

A: Given     Discharge, Q = 14361.60 gpm = 0.91 m3/s         Length, L = 1000 ft = 304.8 m…

Q: A cylinder is moving a 6000 lb load up a 20° slope as shown in the figure below. The friction…

A: Given: Angle of inclination→θ=20° Friction coefficient between the surfaces→μ=0.4 Mass of the…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.