A hydraulic power pack is to be used in a test house which undertakes fatigue and reliability investigations. The fluid demand can vary from 5-100 1/min and be at pressures up to 300 bar. The fluid must be pulse free and filtered to ß3 = 75. Draw a suitable pumping circuit bearing in mind the importance of system reliability. (If a test is stopped part way through any results will be meaningless.)

A hydraulic power pack is to be used in a test house which undertakes fatigue and reliability investigations. The fluid demand can vary from 5-100 1/min and be at pressures up to 300 bar. The fluid must be pulse free and filtered to ß3 = 75. Draw a suitable pumping circuit bearing in mind the importance of system reliability. (If a test is stopped part way through any results will be meaningless.)

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Two steel columns P (LengthL end yield strength = 250 MPa) and a (length 2L and yield strength = 500 MPa) have the same cross-sections and end- fy conditions. The ratio of buckling load of column P to that of column Q is
stucked here
Problem 4: A four-cylinder 50KW MPFI-SI engine is in need of fuel injectors which can generate a spray with a SMD of 70microns. Develop an algorithm and flow chart to design an injector. State all the property data and specifications required to use your algorithm.
A chemical process takes place in a reactor vessel continuously, but it has to be monitored for abnormal behaviour. The system has two sensors S1 and S2 that can independently detect an abnormal temperature. They pass an electrical signal to an electrical OR-gate A, which passes a signal on to both the protection units P1 and P2 if either sensor gives a signal. The protection units and the OR-gate get electrical power from electric power unit E1, while sensors get power from electric power unit E2. Build a (qualitative) fault tree for the top event "Protection system not available" using failure of the indicated components.
What is the allowable stress if the Factor of Safety is 3 and the Yield strength is 35.5 MPA?
(d) It is desired to monitor the running of three fans using two light emitting diodes (LED’s). The required specification is as follows: (i) If no fan is running, no LED is to be activated. (ii) If one fan is running, the first LED is to be activated. (iii) If two fans are running, the other LED is to be activated. (iv) If three fans are running, both LED's are to be activated. Sketch a ladder logic diagram to implement this specification.
Need the 1st one's answers sir.
Answer this question. Part (4), (5) & (6).
8. If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is (a) stable .... (b) unstable (c) any of the above.
Q1: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN. Determine the smallest allowable outside diameter of the tube if the working stress is 110 MN/m? Q2: The 20-mm-diameter bolt fastens two wooden planks together.. Find the smallest thickness of each plankes if the working bearing stress for wood is 13 MPa.
25. To design analogue computer for solving the first-order system: Y(s) G(s) 0 10,0 < b ≤ 10 U(s) s+b 1. What are the possible ways of connections? 2. When it will be used for each connection?
(a) How should the description in Problem 5.30 (a) be written to have the same behavior when the assignments are made with=instead of with <= ?2. (b) How should the description in Problem 5.30 (b) be written to have the same behavior if A, B, C, D, and E are variables and the assignments are made with=instead of <= ?