A radio system transmits a 2.4GHz signal at 250mW over a distance of 20m through two antennae with a combined gain of 10dBi. If the noise level is 0.05µW, and the bandwidth the channel is 250kHz, what is the theoretical maximum capacity of the system?

Q: systen operating at an information rate of 36 kbps determine, Baud Minimum bandwidth

A: The Answer is in Below steps

Q: What is the maximum allowable distance for horizontal cabling? 100 m

A: The horizontal option secures and separates the cables while within the rack. While moving up or…

Q: Q1. In a communication system, a power of 10 dBm is transmitted through a dipole antenna. The power…

A: Given Data : Transmitted Power = 10 dBm Power Received at distance 1 m  = 31.4 dB. Exponent value…

Q: Data communication In a system with a bit rate of 3Mbps ,it is desired to send 3 bits at once…

A: In this question we have to solve for the given data. Calculate the levels, baud rate and bandwidth…

Q: A telephone line uses speech signal of 4KHz and 8bit pattern to send 10kbps,the number of harmonics…

A: EXPLANATION Below is the answer for the given question. Hope you understand it well. If you have any…

Q: Evaluate the modulation dep Calculate the carrier power, Draw the block diagram mathematical…

A: Evaluate the modulation depth m, and mention the type of this AM system. The modulation depth (m)…

Q: An 16-QAM modulator transmits data at the bit rate of 200 Kbit/s thorough an AWGN channel with PSD…

A: 3

Q: Decomposing periodic analog signal into two sine waves having a phase shift equivalent to 1/6 and…

A:

Q: The correct matching of the given table is A 3500 Hz signal 1 ELF B 250 Hz signal 2 VLF C 350 MHz…

A: Match the correct answers.   Note: Kindly read the frequency range table mentioned in step 2, where…

Q: For SNR of 12.33 dB and signal power .4 of 22.23 mW, the value of noise power :is 1.3 mW O 0.3 W O…

A: Formula=SNR=Signal power/ Noise power Given SNR in dB so we will first convert it into normal.…

Q: Given tsu -0.6ns, th=0.2ns, to=[0.8ns, 1.2ns], and tAND-1.5 ns, what is the minimum clock period…

A: Answer is: option DExplanation:Step 1: Step 2: Step 3: Step 4:

Q: Q1/A/ DM system is designed to operate 3times the Nyquist rate for a signal with a 3KHZ Bandwidth…

A: Provided the solution for both the above given questions, with detailed step by step explanation as…

Q: If a system has an average power level of 200, an average noise level of 6.66, and a bandwidth of…

A: The Answer start from step-2.

Q: Problem 3 The modulating signal m(t) = 4 cos(200t) cos(400nt) is multiplied by the carrier c(t) =…

A: Since you have asked multiple question ,we will slove the first question for you .If you want any…

Q: If the power supplied to a system is 10kW, what is the voltage across the line if the current is…

A: The power is given by, where, P- Power V- Voltage I- Current Given: Power "P"= 10kW=10000W Current…

Q: andwidth of the light for the following wavelength ranges (assume a propagation speed of 2x108…

A: Assume a propagation speed of 2x108 m/sec 1000 to 1200 nm 1000 to 1400 nm

Q: Assume that the 60-dB bandwidth of a receiver is 12 kHz and the 6-dB bandwidth is 7 kHz. What is the…

A: Given : 60 dB Bandwidth of a receiver = 12 kHz 6 dB Bandwidth of a receiver = 7 kHz We need to…

Q: If the signal at the end of a 6km cable has a power value of 2, if you knew that this cable loses…

A: Given length=6km loss=0.5dB/km

Q: 2. If the period of a PWM signal is 1500 counts and the desired duty cycle is 20%, what is the pulse…

A: 1) The duty cycle describes the amount of time the signal is in a high (on) state as a percentage of…

Q: If a carrier signal v,(7) = 20sin(25000r) Volts is amplitude modr- 1, () = 4 sin (272001)–6…

A: Bandwidth of AM signal is  2*Fm Fm is the maximum message signal frequency frequency plot and…

Q: Given tsu =0.6ns, th=0.2ns, tcq=[0.8ns, 1.2ns], and tAND=1.5 ns, what is the minimum clock period…

A: In digital circuits, the clock period refers to the time interval between two consecutive clock…

Q: a: Design of Microstrip antenna which operating at frequency of 890 MH2 using the program hfss

A: It is defined as a low-profile antennas. A metal patch mounted at a ground level with a di-electric…

Q: When the mobile is moving in the direction of signal source with speed = 120 km/hour and the carrier…

A: The bandwidth of the signla u1c1 is 20khz

Q: HW5 Consider the analog signalx(t) given by x(t) = 3 cos(50at) +100 sin(300 rt) - cos(100Tt) What is…

A: nyquist rate is twice the maximum frequency .  Nyquist rate=2*Fmax

Q: Two LOS antennas with heights h1=25m and h2=100m are supposed to see each other. Calculate the free…

A: Given, h1 = 25 meter And, h2 = 100 meter   We have to calculate the maximum distance between two…

Q: Power in Amplitude Modulation at 100% Modulation An un modulated AM signal produces a current of…

A: Power in Amplitude Modulation at 100% Modulation  current of 7.3 A  impedance 60 Ω.

Q: A channel carries information at a signal-to-noise ratio of Ldb = 13 . Find the capacity of this…

A: Here We use Formula Shannon channel capacity C = B.log2(1+SNR) (in bits/second)  where B is the…

Q: Output Port Load Output Port PIC crocontroller

A: ANSWER:The correct answer to the given question  is Option("a") "155 ohm"