A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 65-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m.K). Do D₁2 Dil ↓ ↓ Water 1+1=3 mm Gas h Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m².K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. q=i W/m

A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 65-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m.K). Do D₁2 Dil ↓ ↓ Water 1+1=3 mm Gas h Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m².K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. q=i W/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Task 2 A heat exchanger that is used for cooling lubricating oil is comprised of a thin-walled inner tube of 30 mm diameter carrying water and an outer tube of 50 mm diameter carrying the oil. The exchanger operates in counterflow mode with an overall heat transfer coefficient of 65 W/m² K and the tabulated average properties are given. Properties Water Oil p (kg/m³) 1000 4200 Cp (J/kg-K) v (m²/s) 7 x 10-7 k (W/m .K) 0.64 4.7 Pr 800 1900 1 × 10-5 0.134 140
A shell-and-tube heat exchanger with 1-shell pass and 20-tube passes is used to heat glycerin (Cp = 2480 J/kg.0C) in the shell, with hot water in the tubes. The tubes are thin-walled and have a diameter of 1,5 cm and length of 2 m per pass. The water enters the tubes at 100 0C at a rate of 5 kg/s and leaves at 55 0C. The glycerin enters the shell at 15 0C and leaves at 55 0C. Determine the mass flow rate of the glycerin and the overall heat transfer coefficient of the heat exchanger. (You can use the figure in the next page.)
I need the answer quickly
A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 70-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). D₂ D₁₂ D₁ ↓ 7 Water +1=3 mm Gas h Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m².K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. 9 = W/m
A long thin-walled double-pipe heat exchanger with tube and shell diameters of 1.0 cm and 2.5 cm, respectively, is used to condense refrigerant-134a by water at 20°C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi = 4100 W/m2·K. Water flows through the shell at a rate of 0.3 kg/s. Determine the overall heat transfer coefficient of this heat exchanger.
You are then asked by your supervisor to design a concentric tube heat exchanger to operate under the following conditions: Cold Fluid m = 0.125 kg/s Cp 4200 J/kgK T₁ = 40°C To = 95°C Hot Fluid: m = 0.125 kg/s Cp = 2100 J/kgK T₁ = 210°C If the heat exchanger is characterised by uniform overall heat transfer coefficient, using the LMTD method, determine: e) The maximum possible heat transfer rate. f) The heat exchanger effectiveness. g) The ratio of the heat transfer area under parallel flow to the heat transfer area under counter flow. Comment on the answer.
A liquid is to be cooled from 60 oC to 20 oC using water entering countercurrent at 15 oC and leaving at 25 oC in a double pipe heat exchanger composed of ¾” Sch. 40 and 1.5” Sch. 40 steel pipes. Entering velocity of liquid is 1.5 m/s. ho = 5000 W/m2-K; hi = 1500 W/m2-K; k of pipe = 44 W/m-K. Determine the overall heat transfer coefficient Ui in W/m2-K.
Determine the length needed for a simple concentric-tube, parallel flow heat exchanger to transfer heat from hot water to cold water at a rate of 900 W. The heat exchanger consists of two Type K copper (k=386 W/m-degC) tubes. The smaller tube has an inside diameter of 49.8 mm and an outside diameter of 54.0 mm. Assume that both film coefficients are equal to 100 W/sq.m.-degC. The hot water enters at 90 degC and leaves at 50 degC, and the cold water enters at 10 degC and leaves at 40 degC.
Hot coolant water is supplied to a shell and tube heat-exchanger with two shells and twelve tube passes at rate of 1.5 kg/s and a temperature of 350°C. The heat exchanged is used to warm 2.6 kg/s of process water from 15°C to 125°C. Determine the required heat-transfer surface-area when the overall heat transfer coefficient is 1700 W/m-K. You may assume that the water pressure is sufficiently high so that no phase changes occur within the system and the water specific heat is constant at 4.18 kJ/kg.K. Answer: m2
Consider two heat exchanger configurations: parallel-flow and counter-flow. For both configurations cooling water at a flow rate of 1.5 kg/s enters the heat exchanger at 30°C and exits at 45.1°C. This water cools unused engine oil at a flow rate of 1 kg/s from 95°C to 50°C. Both configurations have the same overall heat transfer coefficient of 9,000 W/m2/K. Determine the following: 1. What is the required heat transfer area for each configuration? 2. Give that both configurations have the same inlet and outlet temperatures, what is the basis of the different areas calculated in part a?
In order to cool a mass flow rate of 55 Kg/h of air (cp = 1060 J/KgoC) at 300o C, it is passed through the tube side of a counter flow heat exchanger with a length of 2 m and 2.54 cm tube outer diameter. Thecooling water, (cp = 4182 J/Kg o C and ρ = 1000 Kg/m3 ), enters the heat exchanger at a temperature of 30o C with a volume flow rate of 0.6 Litre/min. If the overall heat transfer coefficient, U, is 5.83 W/m2oC andthe effectiveness of the heat exchanger 60 %, calculate the following:a. The heat transfer rate,b. The exit temperatures of both the water and the air,c- The surface area of the heat exchanger,
A shell-and-tube heat exchanger is used for cooling 47 kg/s of a process stream flowing through the tubes from 160°C to 100°C. This heat exchanger has a total of 100 identical tubes, each with an inside diameter of 2.5 cm and negligible wall thickness. The average properties of the process stream are r = 950 kg/m3, k = 0.50 W/m·K, cp = 3.5 kJ/kg·K and m = 2.0 mPa·s. The coolant stream is water (cp = 4.18 kJ/kg·K) at a flow rate of 66 kg/s and an inlet temperature of 10°C, which yields an average shellside heat transfer coefficient of 4.0 kW/m2·K. Calculate the tube length if the heat exchanger has (a) a one-shell pass and a one-tube pass and (b) a one-shell pass and four-tube passes.