A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 70-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). D₂ D₁₂ D₁ Į Water Gas 1-3 mm w Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m²-K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. q=1 W/m

A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 70-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). D₂ D₁₂ D₁ Į Water Gas 1-3 mm w Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m²-K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. q=1 W/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam condenses at 100°C on the outer surface of a pipe with a thermal conductivity of 180 J/ms°C. The surface heat transfer coefficient of the water flowing in the pipe is 4000 J/m²s°C, and the heat transfer coefficient created by the steam condensing outside is 10000 J/m²s°C. The length of the pipe is 5 m and the thread diameter is 25 mm. Since the pipe thickness is 1 mm, calculate the total heat transfer coefficient and the rate of heat transfer from the condensed steam to the water at 15 °C
A double tube heat exchanger operating in parallel is used to heat water compressed in the liquid phase from 20°C to 80°C through the use of a fluid initially at 160°C which, upon flowing through the heat exchanger, has its temperature reduced to 120°C. Consider that the inner tube is metallic, with a roughness height equal to 0.05 mm, with internal and external diameters equal, respectively to 27.9 mm and 33.4 mm, and whose resistance to conduction heat transfer can be disregarded. Knowing that the water flows into the inner tube with a mass flow of 1.0 kg/s and that the convective coefficient observed between the hot fluid and the outer surface of the inner tube is equal to 3000 W/(m2 .K). Determine: The exchange area and the corresponding length of the tube using the logarithmic mean temperature difference method - MLDT
An electric heater heats the inner tube walls of a concentric tube annulus at a rate of 2000 W/m. The inner and outer tube diameters are 25 and 50 mm respectively. Water enters the annular region at 25 ⁰C and leaves at 85 ⁰C. The flow rate of water is 0.04 kg/s and the outer tube wall is insulated. Assuming that fully developed conditions exist at the outlet, the inner tube surface temperature at the outlet will be ?
A counterflow, concentric tube heat exchanger is designed to heat water from 34 to 80 deg C using hot oil,which is supplied to the annulus at 174 deg C and discharged at 140 deg C. The thin-walled inner tube has a diameter of Di=34 mm and the overall heat transfer coefficient is 500 W/m2. K. The design condition calls for a total heat transfer rate of 4400 W. What is the length of the heat exchanger? Select one: a. 0.82485 b. 1.0478 c. 0.95849 d. 0.7013
a one shell and two tube pass heat exchanger, coolant enters the tube at 4.81 kg/s (spread over 72 tubes with each tube being 0.01 m in diameter and 1.95 m length) at an initial temperature of 25 C. Water enters the shell at 2.5 kg/s at an initial temperature of 5 C. The average convection coefficient of the water is known to be 1e4 W/m2.K. What is the overall heat transfer coefficient, assuming no fouling, negligible tube thermal resistance and near-identical inner and outer tube surfaces? What is the actual heat transfer rate? What is the coolant outlet temperature? The coolant properties are Cp = 1040 J/kg.K, μ = 7.65e-4 kg/s.m, k = 0.058 W/m.K and Pr = 14. Assume the water Cp = 4200 J/kg.K.
A condenser consists of 5 pieces of 3 m long 1/4 in Sch 40 horizontal pipes lined up in 6 rows. It transfers cooling water with a heat transfer coefficient of 2000 W / m-K through the pipes. As the flow rate of the water is very high, the water temperature is constant at 35 degrees Celsius. Saturated heat vapor condenses at a pressure of 2 bars outside the pipes. Calculate the condenser capacity in kW
A counterflow, concentric tube heat exchanger is designed to heat water from 23 to 80 deg C using hot oil,which is supplied to the annulus at 163 deg C and discharged at 140 deg C. The thin-walled inner tube has a diameter of Di=23 mm and the overall heat transfer coefficient is 500 W/m2. K. The design condition calls for a total heat transfer rate of 3300 W. What is the length of the heat exchanger? Select one: a. 0.49417 b. 1.1269 c. 0.92237 d. 0.6234
A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat water (unmixed) from 30 to 70 °C at a rate of 3 kg/s. The exhaust gases, having thermophysical properties similar to air, enter and exit the exchanger at 200 and 100 °C, respectively. If the overall heat transfer coefficient is 200 W/m2 ·K, estimate the required surface area. Hint : from 30 to 70 °C at a rate of 3 kg/s.
Calculate the liquid flow rate for a heat exchanger with one tube pass. The liquid is heated from 20°C to 93°C by a hot gas at 260°C and 0.45 kg/s. A-4.64 m², U-280 W/m²
Q) Compare the heat transfer coefficients under the following conditions (Assume flow is turbulent). (1) Two fold increase in the diameter of the tube; the flow velocity is maintained constant by a change in the rate of liquid flow. (2) Two fold increase in the flow velocity by varying the mass flow rate. Comment on. the results.
A shell-and-tube heat exchanger is used to cool compressed liquid methanol from 176 °F to 104 °F. The methanol flows on the shell side of the exchanger. The coolant is water that rises in temperature from 50 °F to 86 °F and flows within the tubes at a rate of 68.9 kg s-1. Finding the appropriate thermophysical data and applying the proper equations, you are required to do the following:
A long, thin-walled double-pipe heat exchanger with tube and shell diameters of 0.01 m and 0.025 m, respectively, is used to condense refrigerant-134a with water at 20°C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi= 4100 W/m² °C. Water flows through the shell at a rate of 0.3 kg/s. The thermal resistance of the inner tube is negligible since the tube material is highly conductive and its thickness is negligible. Both the water and refrigerant-134a flows are fully developed. Properties of the water and refrigerant-134a are constant. Water properties: p = 998 kg/m³, v=u/p-1.004x 10-6 m²/s, k = 0.598 W/m. °C, Pr = 7.01 Cold water D Do