A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 40-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). --1 = 3 mm D. D,2 h Water Gas Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m²-K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. W/m Physical Properties Mathematical Functions

A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 40-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). --1 = 3 mm D. D,2 h Water Gas Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m²-K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. W/m Physical Properties Mathematical Functions

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a one shell and two tube pass heat exchanger, coolant enters the tube at 4.81 kg/s (spread over 72 tubes with each tube being 0.01 m in diameter and 1.95 m length) at an initial temperature of 25 C. Water enters the shell at 2.5 kg/s at an initial temperature of 5 C. The average convection coefficient of the water is known to be 1e4 W/m2.K. What is the overall heat transfer coefficient, assuming no fouling, negligible tube thermal resistance and near-identical inner and outer tube surfaces? What is the actual heat transfer rate? What is the coolant outlet temperature? The coolant properties are Cp = 1040 J/kg.K, μ = 7.65e-4 kg/s.m, k = 0.058 W/m.K and Pr = 14. Assume the water Cp = 4200 J/kg.K.
The condenser of a large thermal power plant is a body-tube type heat exchanger consisting of a single body and 30000 pipes with two passes each. The pipes are thin-walled with an inner diameter of 25 mm, and steam condenses on the outer surfaces of the pipes with a convection coefficient of 11000 W / m2.K. The heat transfer required by the heat exchanger is 2000 MW, and it is provided by the flow of water through the pipes at a flow rate of 30000 kg / h. Water enters at 20 ° C, steam condenses at 50 ° C. Calculate the temperature of the cooling water leaving the condenser? Determine the required pipe length per pass? The properties of water at Tort = 300 K; Cp = 4180 j / kgK, μ = 855 × 10--6 Ns / m2, k = 0.613 W / mK, Pr = 5.83.
A condenser consists of 5 pieces of 3 m long 1/4 in Sch 40 horizontal pipes lined up in 6 rows. It transfers cooling water with a heat transfer coefficient of 2000 W / m-K through the pipes. As the flow rate of the water is very high, the water temperature is constant at 35 degrees Celsius. Saturated heat vapor condenses at a pressure of 2 bars outside the pipes. Calculate the condenser capacity in kW
A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 45-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). D₂ D₁,2 Dil ↓ Water 1=3 mm Gas h Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m².K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. 9 = i W/m
A single-pass, cross-flow heat exchanger uses hot exhaust gases (mixed) to heat water (unmixed) from 30 to 70 °C at a rate of 3 kg/s. The exhaust gases, having thermophysical properties similar to air, enter and exit the exchanger at 200 and 100 °C, respectively. If the overall heat transfer coefficient is 200 W/m2 ·K, estimate the required surface area. Hint : from 30 to 70 °C at a rate of 3 kg/s.
A parallel flow heat exchanger is to be designed to heat 4535 kg/hr of water from 21°C to 43°C with the steam condensing at 121°C on the outside of the tubes. Tubes of 2.54 cm outside diameter and 2.286 cm inside diameter, 2.44m long, are available for use. Assuming that the average steam-side coefficient is 5675 W/m²-°C, and the thermal conductivity of the tube metal is 110.73 W/m²-°C, calculate the required number of tube per pass. Assume that the velocity of the water entering each tube is equal to 0.457 m/sec. a. 7 c. 9 b. 8 d. 10
Consider the flow of motor oil (cp=2048 J/kg K) through a copper tube ofthin wall at a rate of 0.3 kg/s. The oil enters the copper tubes at atemperature of 80°C that is cooled by means of water that enters at 20°C. Temperatureoutlet of the oil cannot be higher than 40°C. The convective coefficient ofheat transfer from the oil side is 750W/m2 K and from the water side 350W/m2 K. IfThe outlet temperature of the water is measured at 32°C and a heat exchanger is considered.double tube in parallel. Determine: a) Mass flow rate of the water. b) The difference of log mean temperatures. c) the area of the heat exchanger.
A heat recovery device involves transferring energy from the hot flue gases passing through an annular region to pressurized water flowing through the inner tube of the annulus. The inner tube has inner and outer diameters of 24 and 30 mm and is connected by 8 struts to an insulated outer tube of 75-mm diameter. Each strut is 3 mm thick and is integrally fabricated with the inner tube from carbon steel (k = 50 W/m-K). D₂ D₁₂ D₁1 ↓ Water +1=3 mm Gas h Consider conditions for which water at 300 K flows through the inner tube at 0.161 kg/s while flue gases at 800 K flow through the annulus, maintaining a convection coefficient of 100 W/m²-K on both the struts and the outer surface of the inner tube. What is the rate of heat transfer per unit length of tube from gas to the water? Use the Dittus-Boelter equation to obtain the water-side convection coefficient. Determine the rate of heat transfer per unit length of tube from gas to the water, in W/m. q=1 W/m
Calculate the liquid flow rate for a heat exchanger with one tube pass. The liquid is heated from 20°C to 93°C by a hot gas at 260°C and 0.45 kg/s. A-4.64 m², U-280 W/m²
Q) Compare the heat transfer coefficients under the following conditions (Assume flow is turbulent). (1) Two fold increase in the diameter of the tube; the flow velocity is maintained constant by a change in the rate of liquid flow. (2) Two fold increase in the flow velocity by varying the mass flow rate. Comment on. the results.
part d
It is proposed to cool oil in a counter-current, concentric tube heatexchanger composed of a thin-walled inner tube of 0.02 m diametercarrying oil and thin-walled, perfectly insulated outer tube of 0.05 mdiameter carrying water. The oil flow rate is 50.0 kg min-1 and it has to becooled from 90°C to 40°C using 60 kg min-1 water at 20°C. Determine the length required for the heat exchanger. Comment onthe practicality of this length.