A gearset consists of a 16-tooth pinion driving a 40-tooth gear. The diametral pitch is 2, and the addendum and dedendum are 1/P and 1.25/P, respectively. The gears are cut using a pressure angle of 20°. (a) Compute the circular pitch, the center distance, and the radii of the base circles. (b) In mounting these gears, the center distance was incorrectly made in larger. Compute the new values of the pressure angle and the pitch-circle diameters.

A gearset consists of a 16-tooth pinion driving a 40-tooth gear. The diametral pitch is 2, and the addendum and dedendum are 1/P and 1.25/P, respectively. The gears are cut using a pressure angle of 20°. (a) Compute the circular pitch, the center distance, and the radii of the base circles. (b) In mounting these gears, the center distance was incorrectly made in larger. Compute the new values of the pressure angle and the pitch-circle diameters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please use the following table and please the ratio is not 1.714 this answer is wrong. Please don’t reply with same answered way previously!!!!
plz solve 4 and 5 where X = 5
An epicyclic gear shown in figure below consists of ring gear, planet gear and sun gear. The ring gear has 72 internal teeth and sun gear has 32 external teeth. Planet gear meshes with both ring and sun gears and is carried on an arm which rotates about the centre of the ring gear at 20 r.p.m. If the gear A is fixed, Calculate the speed of plane gear.
Use the right formula. A 20 degree-pressure-angle, 22-tooth spur gear has a diametral pitch equal to 5. Calculate the dedendum in mm
i need the answer quickly
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.
73 ll 6 O ... The pitch circle radius multiplied by the cosine of the pressure angle. Q3:- The increase of the contact ratio is desirable in gearing design because of:- * All of these The number of teeth will be increased in the engagement region More strength and more gear life will be achieved Smoother and faster motion None of these Q4:- To get best gearing design, it requires to:- * Increase sliding None of these Decrease sliding
lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle. Determine the velocity ratio and the pitch angles. of both gears.
Three 14.5° pressure angle spur gears with a diametral pitch of 8 are meshed. The input pinion on the left is running clockwise at 3101 rpm and transmits 3.2 Hp. Gear 1 (Pinion) Input N1 = 20 teeth Gear 2 Idler Gear 3 Output N3 = 25 teeth N2 = 75 teeth Answer the following: 1. Pinion (Gear 1) pitch diameter (1 mark) 2. Gear 2 pitch diameter (1 mark) 3. Gear 3 pitch diameter (1 mark) 4. Circular pitch (1 mark) 5. Addenda (1 mark) 6. Center distance from gear 1 to gear 3 (2 marks) 7. Line of action length for gear 1 contacting gear 2 (2 marks) 8. Contact ratio of gear 1 and 2 (2 marks) 9. Gear ratio from gear 1 to gear 3 (1 mark) 10. Draw a free-body diagram of Gear 2, showing the radial and tangential forces. Calculate these forces. What is the reaction force in the bearing? (3 marks)
i. A parallel helical gearset uses a 20-tooth pinion driving a 46-tooth gear. The pinion has a righthand helix angle of 30•, a normal pressure angle of 20•, and a normal diametral pitch of 6 teeth/in. Find: (a) The normal, transverse, and axial circular pitches (b) The normal base circular pitch (c) The transverse diametral pitch and the transverse pressure angle (d) The addendum, dedendum, and pitch diameter of each gear
i need the answer quickly
The Question is from Kinematics of Machine. Please Solve it .