A force F = (0.5i - 2.0j + 7.0k) kN acting at A(5, -4, 0)m about axis BC where B(6, 8, 4)m and C(-6,-5, 8)m, What is the perpendicular distance between F and the axis BC in meters? 7.890 B 1.810 10.81 11.801 9.018

A force F = (0.5i - 2.0j + 7.0k) kN acting at A(5, -4, 0)m about axis BC where B(6, 8, 4)m and C(-6,-5, 8)m, What is the perpendicular distance between F and the axis BC in meters? 7.890 B 1.810 10.81 11.801 9.018

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the reactions and draw the shear and bending moment diagrams for the beam. Use the slope…

Q: F2=400L6 F3=60016 Fi=70olb 30° Detremine the magnitude of the resultant force acting on the corbel…

A: break force into components to get the resultant.

Q: The 12.5-cm-diameter 20°C water jet in the figure strikes a plate containing a hole of 10.5-cm…

Q: For the section shown: 500mm 450 *75mm Determine the location of the plastic neutral axis from the…

Q: Find the magnitude of the net force on the following object (A) given: |F1|=3.2 N |F2 -9.8 N |F3❘ =…

Q: Q3. What is the relative displacement of points A and B when subjected to forces P. Consider only…

A: Relative displacement, which is displacement of a point on a structure with respect to its original…

Q: w = N/m Omax 764EI at x = 0.475L

A: This is fixed beam with uniformly varying load and find out deflection at x = 0.475L.

Q: 3.16 Three forces of 900 lb, 1000 lb, and 600 lb are acting on a boat. The first force acts due…

A: Note: Dear student as per our company guidelines i am solving first problem only (i.e problem 3.16…

Q: 30° DONE noiluted 008-114 ME=A 3. A in the figure shown, the homogeneous block weighs 300 KN and the…

A: GIVEN: TO CALCULATE: Force P and h to cause motion to impend. CONCEPT: Use Equilibrium Equations.

Q: Situation 7:The steel bar BC is supported by the steel rod AC of cross-sectional area of 170 mm², E…

Q: Determine the slope and displacement at A.E = 29X10^6 psi, I=1800 in^4 using a) moment area…

A: Introduction- The moment-area hypothesis is a mathematical formula for calculating the slopes,…

Q: Compute the x-component of the resultant of the concurrent forces shown in N. P1 185 N, P2 = 347 N,…

A: Using formula

Q: | Refer to a robot shown. If P = 360 kN Which of the following most nearly gives the moment at point…

Q: Analyze the given structure using Slope Deflection Method 30KN/m 100KN D E 5m 10m 15m 5m El -…

Q: PROB. 21 22. A beam made up of two unequal leg angles is subjected to a bending moment M having its…

Q: F 35

Q: Situation 9. A continuous beam with a span of 20m is supported at both ends by a hinged support and…

Q: (0.80) D The 5 ft diameter cylinder weighs 5000 lbs. and is 5 ft long as shown. Determine the…

Q: 7. The sports car, having a mass of 1700 kg, travels horizontally along a 20 banked track which is…

A: Given data: Mass of car=1700 kg Radius of curvature=100 m It is asked to determine the normal…

Q: *3-100. If F. = 7 kN and Fa = 5 kN. represent the force system by a resultant force, and specify its…

A: Consider the figure with the dimensions as shown below. The resultant force vector is calculated…

Q: Example 2.9. A horizontal line PQRS is 12 m long, where PQ = QR = RS = 4 m. Forces of 1000 N. 1500…

Q: The mass of block B is 95kg while that of A is 59kg. A horizontal force P=468N is applied at block…

Q: For the beam loaded as shown, determine the beam deflection at point C. Assume that E = 25500 ksi…

A: Intensity of UDL (w) = 3.2 kips/ft Intensity of point load (P) = 36 kips Young's modulus of…

Q: Determine the maximum horizontal force P that can be applied to the 30-lb hoop without causing it to…

A: The free body diagram of the hoop is given below.

Q: Resolve the 900-N force into a component P along with AB and a component Q perpendicular to AB. B…

Q: Analyze the structures shown by slope deflection method. Draw the shear and moment diagrams

A: ###SFD and BMD of a frame using Slope Deflection Method ###

Q: Determine the magnitude of the resultant force and itsdirection, measured counterclockwise from the…

A: Given that Fx=85045-750 sin 45°-625 sin 30°Fx=-162.83 NFy=-85035+750 cos 45°-625 cos…

Q: The submerged curve AB is one quarter of a circle of radius 3 m and is located on the lower corner…

A: Given Required Location and magnitude of horizontal and vertical components of force on AB

Q: Q7. Use the method of conjugate beam to find the slope and defection at a distance of 2m from the…

A: Given Data IAB = 5000 cm4 Determine the slope and deflection at 2m from free end using Conjugate…

Q: Consider the same beam (orientation a) in Q1. If b=20 cm and h = 10 cm, and if the beam material has…

A: Width of beam (b) = 20cm = 200 mm Depth of beam (h) = 10cm = 100 mm Maximum allowable stress = 100…

Q: The 9-cm diameter 20 degrees Celsius water in the figure strikes a plate containing a hole of 7-cm…

A: Given data D1 = 9cm = 0.09 m D2 = 7cm = 0.07 m Assume density of water = 1000 kg/m3

Q: Determine the displacement at B using Moment-Area Method

Q: 6a. A vertical force of 80 lb acts on a crankshaft that is held in place by a bearing at A that…

A: Given Data -

Q: A wire makes angles of 35° and 55° at support A and B, respectively, as shown. If the wire has a…

A: Given cable is in parabola .mass density of parabola is 0.5kg/m. Horizontal angle at support A = 35…

Q: n the figure 9, assume clockwise moments as positive, force F= 432KN nd force P =500 KN. Calculate…

Q: 120KN 120KN 150KN A. 6m 4m B 6m 4m 4m 4m 21 Analyze the structure using Moment Distribution Method…

Q: Determine the displacement at point B by the method of Virtual Work in Q.5. EI is constant. 8k 3k/ft…

A: Method of virtual work is the method of virtual forces that allows the law of conservation of energy…

Q: Compute the resultant of the concurrent forces shown in N. P1 = 254 N, P2 = 490 N, P3 = 414 N, P4 =…

Q: Determine the smallest horizontal force P required of static friction at the contact points A and B…

Q: 6. Determine the magnitude of the resultant R, if P2 = 978, P3 = 780.

A: Magnitude of vector R is given by equation 9 in step 3 as ∣R∣=321.42.Explanation:Step 1: Given and…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

A force F = (0.5i - 2.0j + 7.0k) kN acting at A(5, -4, 0)m about axis BC where B(6, 8, 4)m and C(-6, -5, 8)m, What is the perpendicular
distance between F and the axis BC in meters?
7.890
1.810
(c) 10.81
11.801
E) 9.018
F
9.810
G
8.091
H.
6.809

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 : Given

VIEW

Step 2 : Solution

VIEW

Step 3 : Calculation of constant

VIEW

Step 4: Perpendicular distance AD

VIEW

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The rail AB of negligible weight is suspended from a rope that runs around two fixed pegs. The coefficient of static friction between the rope and the pegs is 0.3. As the weight W moves along the rail toward end B, determine its position “x" when the rope is about to slip on the pegs. 3 m D B с. 2.66 m d. 1.66 m a. 1.16 m b. 2.16 m
Blocks A has a mass of 35 kg and B has a mass of 40 kg. All contact surfaces have the same coefficient of friction of 0.3. Determine the force P needed to cause impending motion of block B to the right. Use 8 = 80° and B = 10° B 157
23
Can you please solve these three questions?
A beam is subjected to force as shown in the figure below. Try to analyze the reaction force of the beam at point A and point C. Assuming that the EI of the entire beam section is constant, try to draw the shear curve and bending moment diagram of the beam. (Moment Curve).
For the beam, why is the moment Mo negative? if i were to take the fixed point at A, Mo gives a smiling face which is the convention for positive. However, if i were to take the fixed point at B, Mo gives a sad face which is the convention of negative. So which fixed point should i take to determine the sign convention and why
The Resultant of the concurrent forces in the figure below is R = 348 KN, pointing up along y-axis. Compute the value of F in KN to give this resultant. P1 = 554 and P2 = 286. Write the numerical value only and use two decimal places. P1 R F₁ I+Y F3 Ө 30° F P2 Determine the y-component of the resultant of the concurrent forces in KN below. F1 = 337 KN, 01 = 56, F2 = 498 KN, 02 = 40⁰, F3 = 215 KN, 03 = 22°. Write numerical value only with 2 decimal places + X + Y F₂ Fy yo 0₁ 0₂ + X 03
For the given set of forces shown, determine the following if each side of the square is 1m in length.: a. the type of force system b. the magnitude of the couple c. the resultant moment of the forces about A d. the resultant force e. the perpendicular distance of the resultant force from A. f. the x and y intercepts of the resultant force with respect to the X and Y axes thru A. 100k4) JORN 150 kN 20 ku Goka '50 k 50 kN
Q1) For the force system shown in figure, 1) Find the angle (0) so that the resultant of these forces will be vertical. 55 kN A B45 KN В 3 Ø |C 1m 3 m 3 m
Q/ The (200N) block shown in Fig . Has impending motion up the plane .Coused by e isjall dåg le the Horizontal force Lii 5 gå of ( 400N ). Determine the coefficient of static friction between the contact surfaces alial l. 400N 200N 300
F
Determine the vertical displacement of the cantilever beam at point C.