130 N Q.1) Determine the resultant of the coplanar system shown here. (a) Express the resultant as a Cartesian force vector. (b) Find the magnitude of the resultant force vector. (c) Find the angle of the resultant measured counterclockwise from the positive horizontal axis. 205 N 115 N

Q: QUIZ 3 FALL 2020 Problem 1. For the frame shown in the figure, determine (a) Reactions at the…

A: Solution-

Q: An HSS 16 x 16 x 1/2 (A = 28.3 in?, twall = 0.465 in, r, = ry 6.31 in) with F, = 46 A 18 ft long…

A: Data Given: Column section=16×16×12Gross area =A=28.3 in2b=16 in,  t=0.465 inry=6.31 inL=18 ftFy=46…

Q: IS 25 kg and it causes each spring to be stretched by 500 mm, vhen the 2 blocks are applied; (2) the…

A: Draw the free body diagram at A           apply equation of equilibrium ∑Fx = 0 -TAB cosθ+TADcosθ =…

Q: Infiltration from Precipitation: With an average annual precipitation of 300 mm, 30% of which…

A: Total water infiltrated per year (litres) == Area * annual average precipitation * 30% * 1000= 36…

Q: Draw the shear and bending moment diagram for the given beam. 150N/m B 3m 6m

A: Draw the free body diagram. Equilibrium of horizontal forces,

Q: please solve this homework question I can’t seem to understand

A: Given data - Lcr - lateral distance from the right end Lcl - lateral distance from left edge of…

Q: For an allowable stress of 15 000 psi, what is the maximum design pressure permitted for r/t=5,…

A: Allowable Stress S = 15000psi  r/t = 5 r = inside radius t = required thickness To determine Maximum…

Q: Note: For this question, Reynolds number is not needed, so don't spend time calculating it.…

A: V1 = Q/A1 = 0.015/(3.14*0.14632/4) = 0.8927m/s V2 = Q/A2 = 0.015/(3.14*0.07372/4) = 3.518m/s

Q: A thin layer of clay subjected to drying develops internal shrinkage stresses. The state of…

A: In principle stress, the transformation equations can be represented in graphical form using Mohr's…

Q: 2.68 The homogeneous gate shown in Fig. P2.68 consists of one-quarter of a circular cylinder and is…

A: Given data:

Q: In the structure shown, in diameter pins are used at A, B&D The ultimate shearing stress for the pin…

A: Diameter -  ϕpin = 13in   Ultimate shearing stress -  At point D -  σD = 6ksi  At AB -  σAB = 10 ksi

Q: A metal bar AB of length L is held between rigid supports and is heated non-uniformly in such a…

A: For a  metal bar AB held between rigid supports and is heated non-uniformlyLength= LChange in…

Q: Trigonometry Review

A: Trigonometry review

Q: I think each question should solve three parts.

A: As per Bartleby guidelines only first three subparts of a given question should be answered. Here,…

Q: 1. Determine the moment of inertia about the horizontal centroidal x-x axis for the area shown in…

A:

Q: For the simply supported beam with square cross sectional area as shown in the Eigure below: 1.…

A: FBD of this diagram now calculate the reactions at supports VA+VB=3+5+1×2=10KNtaking moment at B…

Q: Two forces F1 and F2 act on a body. The net force on the body is Fnet = 2 Ni. If F1= 10 Ni – 10 Nj,…

A: As per guidlines we can solve one question at a time, please upload separately,Thanks

Q: In our generation, which technological advancement is NOT TRUE? * Technology has changed the way we…

A: Brief concept- Technology- Technology is the application and the science which eases the work and…

Q: Q.2) A weight W of 10 N is supported by a system consisting of a cable, two pulleys and a…

A: The system of pulley, bars and weight is given asSlider at B is frictionlessTo find:-Force in bar…

Q: The support reactions are as follows: Ax KN. Ay= kN, and MA= kN-m.

A:

Q: The world carbon emissions can be expressed by the following equation: Carbon emissions =…

A:

Q: Determine the net area for the plate PL // x9 with 3/4 in bolts indicate which area controls

A: Diameter of bolt = 3/4 in Number of bolts, n= 6 Size of plate = 1/2' * 9' It is asked to determine…

Q: Y F1=200# Problem # 3 (7 points): The bent pipe resists forces as shown. Determine the moment of…

A: Consider the following given diagram: The moment at a point is the sum of forces acting…

Q: The beam in Figure 2 is pin supported at A and roller supported at B. Calculate an equivalent…

A:

Q: Determine la magnitud de la reacción en el apoyo A, en Ib. Si: P- 302 Ib, h- 11 in., a- 26 in. b- 9…

A:

Q: 4. The figure shows forces and moments acting on a pipe system. Note that the pipe segment AB is on…

A: Given pipe system with force and moments acting on it, Pipe segment FDE is tilted by angle=30° It is…

Q: The ramp of a ship has a weight of F Ib acts in the center of gravity at G. The ramp is supported by…

A: a) NOTE : As in figure units are given in ft but in question it is modified and given in meters (x =…

Q: Water is flowing in the open trapezoidal channel as shown in Figure. 2 m 6.5 m (b) Wetted perimeter…

A:

Q: A stress element is subjected to bi-axial loading as shown in figure. 30 30° www. 30⁰ What will be…

A: For a given element,To find  the maximum principal stress for the given stress element

Q: A steel beam, of lengths a=5 m and b=2 m and a hollow box cross section, is supported by a hinge…

A:

Q: of 22 A simply-supported reinforced concrete rectangular beam 12" wide and 24" deep has a span feet.…

A: Step 1

Q: 1. Explain the effect of too much slump and too little slump? What affects the degree of "slumpness"…

A:

Q: Q.3) Given the following system of three forces (a) express each vector in Cartesian vector notation…

A: Given.  F1 = 170 lb F2 = 300 lb F3 = 240 lb Component of forces in X, Y, Z directions F1x =…

Q: QI: At a certain section, beam has the cross-section _shown in Figure (1) below. The beam is simply…

A: given figure load on beam=450kn/m

Q: The impeller of a centrifugal blower has an exit diameter of 0.6 m, B2 = 30°, and operates at 3600…

A: The question is based on the impeller of the centrifugal blower. The exit diameter, pressure at…

Q: A section of a two-lane highway (7 m wide) on a horizontal curve as shown has a posted speed limit…

A: Given data: Point of curve (PC)=Sta 2+000 Point of Tangency (PT)=Sta 2+510 Speed (V) = 80 kph two…

Q: Q. 3. Determine the reactions and draw the shear and moment diagrams for the frame in Q. 3. El is…

A:

Q: 9. Find the exact value (no rounding) for sin 0 and cos 0 for the given right triangle WITHOUT…

A:

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

A:

Q: 2. An AISI 4142 steel Q&T at 800°F exhibits Syt = 235 kpsi, Syc = 285 kpsi, and &f= 0.07. For the…

A:

Q: a) Calculate the service shear force applied on the connection. b) Calculate the service tensile…

A: Given data: Section of tee bracket = WT 6*32.5 is attached to a column flange  Section of column =…

Q: A circular aluminum tube of length L=500 mm is loaded in compression by forces P (see figure (a)).…

A:

Q: Q.3) The L-frame in figure below supports forces from two cables. Cable "EAD" passes through a…

A: Given: Force in cable EAD = 800lb and in OCG = 400lb Required  Moment about point B, A and O.

Q: 2) The horizontal beam is rigid, and the three bars have the same length. The bars AB and EF are…

A: Given- AB and EF made of aluminium, CD is made of steel, Structure is heated from 50 oF to 90 oF.

Q: Q3. Write shear and moment equations for the beams shown. Also, draw the shear and moment diagrams,…

A: Solution

Q: (a) What is the height of atmosphere above earth surface, if the pressure of air at mean sea level…

A: Pressure at height (h) is given by P=density * g * h where,  P=pressure g= acceleration due to…

Q: Q.4) Rod AB is in the x-y plane and supported by two cables as shown. The tension in cable AC is 910…

A: Tension in the cable AC = 910N Tension in the cable AD =  585N   To be find -  The angle between…

Q: Calculate the volume of material used in making 100 ft of 4-in. type M, copper tubing.

A: Given: Length of tubing, L = 100 ft Nominal size of copper tubing = 4 in Type of copper tubing =…