| Refer to a robot shown. If P = 360 kN Which of the following most nearly gives the moment at point A in Newton-meter.* 137 123 109 153 O 177 Which of the following most nearly gives the vertical component of the force P in * Newtons. 190 265 273 243 295 P 20° 300 mm C 400 mm 'B 60° A O 500 mm

Q: A simply supported wide-flange beam has the cross-section and loading as shown in the figure below.…

A:

Q: Using conjugate beam method determine the value of E18 at 2 ft from R2. Ans. ElōB = 853.32 lb-ft3…

A:

Q: Calculate the shear at a point just after D, in Newton’s ?

A: Given:- A beam is loaded with point loads The magnitude of the point load 1 at C = 200 N  The…

Q: Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the distance…

A:

Q: Figure 50 mm 150 mm 150 mm 300 mm 1 of 1 Locate the centroid y of the bea Express your answer to…

A:

Q: 1. Express the two forces shown as Cartesian vectors. 2. Determine the magnitude and coordinate…

A: Given:- The magnitude of the force along with AB = FAB = 200 N  The magnitude of the force along…

Q: Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the distance…

A:

Q: Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify…

A:

Q: Solve

A:

Q: In figure, Hf in pipe 1 = Hf in pipe 2 =Hf in pipe 3 Pipe 1 Pipe 2 B Pipe3 True O False O

A:

Q: Refer the beam shown with cross section of thickness, t = 15 mm. If F = 84 kN and a = 150 mm, F 2a…

A: All options are incorrect

Q: Find a centroid of area for water tank in Figure 4(a)

A: Given  Dimensions of a combination of two shapes    To find Centroid of the area    Formula

Q: B2. Write the folowing beam deflection for a beam of length L = 4 m as a piecewise function y = 2x…

A: Given ,          y = 2x-x2+13x-33H x-3To find deflection of beam of length L = 4m

Q: Find the value of displacement if force applied is 12 N and work done is 63 i

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Find the value of force along X direction. Force=33 N Angle with X axis is 40 degree

A: Introduction : The given question is related with mechanics topics .In this question we are provided…

Q: The force system shown can be replaced with a single, equivalent couple C. Determine C. Z. 400 N B…

A: Take  Clockwise moments (couple) as positive Counter clock wise moment (couple) as negative

Q: Example: Find x and y components for the force shown. F-316 N 35 degrees

A:

Q: 5.) Consider the 2D beam supported by a roller at A and a pin at B. INTERNAL FORCES f) Is the…

A:

Q: 3. Compute the moment of forces produced about points A and B due to force's F and P. B A P = 3000lb…

A:

Q: 200 mm A 40 mm 50 N 20 mm B. 300 N 250 N 160 mm 100 mm 120 N

A:

Q: Shear stress in neutral axis using the maximum shear force, Make W= 8 kN/m all dimensions are in mm…

A:

Q: Problem 6: Replace the two forces and the negative wrench by a single force R applied at A and the…

A: Feel free to ask any doubt.

Q: Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the distance…

A:

Q: EXERCISE 8. Calculate the vector a x b when a = 2i + j - k and b = 3i – 6j + 2k

A: a=2i+j-k b=3i-6j+2k

Q: As shown in the figure, a force E passing through C causes a clockwise moment of 120 lb-ft about A…

A:

Q: Find the representation of the shown force victor F along the pipe OA, given F= 500 N 5 m 7 m 6 m B.…

A:

Q: Compute for the y-component of the force F2 = 212.5 N at 01= 17.0. 270 230 240 250 022 F₁ 012 002…

A: F2=212.5N θ1=17 To find y component force F2

Q: determin the x and y conponents of the reactions A and B. For reaction B the solution shoukd be in…

A: Determine the support reaction at A and B of the given beam. Note: At pin-C moment is zero.

Q: Asap

A:

Q: The 12 kN-m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the…

A:

Q: Using the SLOPE DEFLECTION METHOD, solve for the following. elastic curve, shear and moment diagrams…

A: To draw shear force and bending moment diagram using slope and deflection diagram.

Q: Help!!! Answer all correctly

A:

Q: X A 90 mm ww 001 F 70 mm B

A: The ans is attached below:

Q: Question 2) In the figure is a Russel broken traction device and a mechanical model of the leg…

A: L = 100cmd = 10 cmTo determineThe tension, T1 in cable 1The angle The tension, T2 in cable 2

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.