A flexible pavement has the following class of loads during a particular hour of the day, i. 80 buses with 2-axles (each axle load of 40 kN): ii. 160 trucks with 2-axles (front and rear axle loads of 40 kN and 80 kN, respectively) The equivalent standard axle load repetitions for this vehicle combination as per IRC:37-2012 would be A. 320 B. 250 C. 240 D. 180

A flexible pavement has the following class of loads during a particular hour of the day, i. 80 buses with 2-axles (each axle load of 40 kN): ii. 160 trucks with 2-axles (front and rear axle loads of 40 kN and 80 kN, respectively) The equivalent standard axle load repetitions for this vehicle combination as per IRC:37-2012 would be A. 320 B. 250 C. 240 D. 180

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter21: Pavement Management

Section: Chapter Questions

Problem 10P

See similar textbooks

Similar questions

A flexible pavement has the following class of loads during a particular hour of the day. i. 80 buses with 2-axles (each axle load of 40 KN); ii. 160 trucks with 2-axles (front and rear axle loads of 40 kN and 80 kN, respectively) The equivalent standard axle load repetitions for this vehicle combination as per IRC: 37-2012 would be
Q5. Given the following information: A concrete pavement for two lane highway has doweled joints and no concrete shoulders. The modulus of subgrade reaction is 200 pci (54.2MN/m3), and the modulus of rupture is 650 psi (4.5Mpa). Assume a load safety factor of 1.1. truck weight distribution data for single axle load is as follows: Axle load(kips) 1 Single axles 28 Multiplied by LSF (1.1) 26 24 2 Expected repetitions 3 Erosion analysis Allowable repetitions 30.8 5,913 28.6 12,483 26.4 15,111 22 24.2 102,492 Using a trial thickness of 8 in. Fill in the empty spaces using PCA design method 4 6. Erosion factor Erosion percent 5
A flexible pavement has the following class loads during a particular hour of the day. i. ii. 80 buses with 2-axles (each axle load of 40 kN) ; ii. 160 trucks with 2-axles (from and rear axle loads of 40 kN and 80 kN, respectively) Find the equivalent standard axle load repetitions for this vehicle combination as per IRC 37-2012.
A roadway project will be constructed in 2026 as flexible pavement, pt-2.5, expected SN= 4 and has a 20-year design life. Design work was done in 2021, with growth rate of 6%. The traffic survey gives axles loads shown in table above. Find the design ESAL according to AASHTO design method. Truck type Axle Category Type-1 1-single axle of 30 kips 1- tandem axle of 32 kips 1-single axle of 18 kips 2- tandem axle of 40 kips 1-single axle of 20 kips 1- tandem axle of 36 kips 1- tandem axle of 50 kips 2-single axle of 22 kips 1- tandem axle of 38 kips 2-single axle of 38 kips 1- tandem axle of 52 kips 2-single axle of 14 kips 1- tandem axle of 32 kips 1- triple axles of 50 kips 1-single axle of 40 kips 1- tandem axle of 32 kips CS Cams Typer triple axies of 58 kips Type-2 Type-3 Type-4 Type-5 Type-6 % Total AADT 9% 10% 7% 5% 3% 5% 4%
You have been asked to design a flexible pavement and the following daily traffic is expected for design: 6375 passenger cars with two 2-kip single axles, 375 18-wheel trucks with one 12-kip single axle and two 32-kip tandem axles, 225 triple-trailer trucks with one 18-kip single axle and six 36-kip tandem axles, and 525 single unit trucks with one 10-kip single axle and one 24-kip tandem axle. There are 3 lanes in the design direction (conservative design is to be used). Assuming a structural number of 5.0, determine the design-lane 18-kip ESALs for the pavement projected 15-year design life with the TSI of 2.5.
A northbound direction on an interstate highway consists of three lanes of flexible pavement. The subgrade CBR is 4.5, the overall standard deviation is 0.38, and the reliability is 95%. The initial PSI is 4.5 and the final PSI is 2.5. Daily total northbound road traffic consists of 39,500 cars (each with two 2kip single axles), 775 buses ((each with two 19 kip single axles) and 1100 heavy trucks (each with two 10kip single axle and two 34kip tandem axles). If the pavement is designed to last for 20 years, what should be its structural number?
You have been asked to design the pavement for an access highway to a major truck terminal. The design daily truck traffic consists of the following: 80 single axles at 22,500 lb each, 570 tandem axles at 25,000 lb each, 50 tandem axles at 39,000 lb each, and 80 triple axles at 48,000 lb each. The highway is to be designed with rigid pavement having a modulus of rupture of 600lb/in2 and a modulus of elasticity of 5 million lb/in2. The reliability is to be 95%, the overall standard deviation is 0.4, the drainage coefficient is 0.9, ¨PSI is 1.7 (with a TSI of 2.5), and the load transfer coefficient is 3.2. The modulus of subgrade reaction is 200 lb/in3. If a 20-year design life is to be used, determine the required slab thickness
The AADTT of a 2-way (2-lane each way) highway is 10,000. The directional distribution may vary between 45 and 55% depending on season. The lane distribution may vary between 60 and 75%. The driving lane always carries more loads compared to the passing lane. The growth factor for the pavement is 3.5%. Based on the above information, calculate the design AADTT for the driving lane if the pavement service life is 20 years.
A flexible pavement was designed for the following daily traffic with a 12-year design life: 1300 single axles at 8,000 Ib each, 900 tandem axles at 15,000 lb each, 20 single axles at 40,000 Ib each, and 200 tandem axles at 40,000 Ib each. The highway was designed with 4 inches of hot-mix asphalt (HMA) wearing surface, 4 inches of hot-mix asphaltic base, and 8 inches of crushed stone subbase. The reliability was 70%, overall standard deviation was 0.5, "PSI was 2.0 (with a TSI of 2.5), and all drainage coefficients were 1.0. What was the soil resilient modulus of the subgrade used in design?
Subject : Transportation Engineering Read the question carefully and give me right solution according to the question. Note: solve by using 45-deg cone pressure distribution method only The maximum wheel load that the pavement could carry is 120 kN. If the contact radius of the wheel is assumed to be 250 mm, and subgrade bearing capacity is equivalent to 0.24 Megapascals, calculate the subgrade layer thickness of the flexible pavement in mm using the 45-deg cone pressure distribution method.
Problem 3. A rigid pavement is to be designed to provide a service life and has an initial PSI of 4.4 and a TSI of 2.5. The modulus of subgrade reaction is determined to be 300 lb/in³. For design, the daily car, pickup truck, and light van traffic is 20,000; and the daily truck traffic consists of 200 passes of single-unit trucks with single and tandem axles, and 410 passes of tractor semi-trailer trucks with single, tandem, and triple axles. The axle weights are cars, pickups, light vans = two 2000-lb single axles (equivalency factor = 0.0002) single-unit trucks = 10,000-lb steering, single axle (equivalency factor = 0.081) = 22,000-lb drive, tandem axle (equivalency factor = 0.305) tractor semi-trailer trucks = 12,000-lb steering, single axle (equivalency factor = 0.1750) = 18,000-lb drive, tandem axle (equivalency factor = 0.132) = 50,000-lb trailer, triple axle (equivalency factor = 3.02)
Problem 1 The total load on a tridem axle is 44 kip. Consider a p, of 2.5 and SN of 4. Calculate the EALF considering flexible pavement.