Determine the intensity of shear of an oil having viscosity 2 poise. The oil is used for lubricating the clearance between a shaft of diameter 15 cm and its journal bearing. The clearance is 2.5 mm and the shaft rotates at 150 rotation per minute.

Determine the intensity of shear of an oil having viscosity 2 poise. The oil is used for lubricating the clearance between a shaft of diameter 15 cm and its journal bearing. The clearance is 2.5 mm and the shaft rotates at 150 rotation per minute.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

Q: Question 1 For the shaft in figure below, the given information's are: • Power 20 KW, at 500 rpm •…

A: P=2πNT60watts20×1000=2×3.14×500×T60T=382.165Nm

Q: 1. A 90-kg smooth circular cylinder A with a radius of 0.6 m is held in equilibrium by a cord CD and…

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Moment at given section due to load PM1=1500×150=225000 N.mmMoment at given section due to load…

Q: 1. An axial compressive load of 50 tons is applied to a metal bar of square section 2 in. by 2 in.…

A: Hjh

Q: A compression spring is made of music wire of 2mm diameter having a shear strength and shear modulus…

A: The change in value of the stiffness=?

Q: Q.8 A solid shaft has 100 mm diameter. It is used to transmits 120™ watt power at 200 rpm (Take G =…

Q: 3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has…

A: Given, Power delivered Where we know that Shaft frequency (f) = 12 Hz

Q: Problem #1: The bar below is composed of three solids cylindrical pieces with the diameters shown.…

Q: A line was measured with a (30m) tape. This is standardized at (20 °C) under a pull of (10kg). The…

A: Given: Length of tape= 30 m Measured length of line = 1500 m Standardized temperature =20°C At 20°C…

Q: A plate 0.03 mm distant from a fixed plate, moves at 80 cm/s and requires a force of 4 N per unit…

Q: n coil diameter is 20 mm, nm and the number of e mean coil diameter is e stiffness of the spring is

Q: mplete solution pls answer in 20 m

A: Take moment about C∑ Mc=0TBA0.125-10000.3=0TBA=2400N∑ Fx=0TBA-Cx=0Cx=2400N∑ Fy=0 Cy=1000N…

Q: A solid cone of radius ro and vertex angle 20 is to rotate at an angular velocity w. The cone is…

Q: a. Celerity of the pressure wave b. Equivalent bulk modulus of water c. Pressure on the pipe after…

Q: Water is placed in a hydraulic press initially at 140kPa absolute, the pressure is increased to…

A: Given, Bulk modulus (k)= 2.5GPa = 2.5×10⁹ Pa bulk modulus(k)= Increase of pressure / Volumetric…

Q: The acrylic plastic rod is 300 mm long and 15 mm in diameter. If an axial load of 200 N is applied…

Q: Problem 1. In a test on an aerosol can it was loaded to a gage pressure p = 69.0 psi. While…

A: inside pressure p=69 psinormal load N=400 lb and torque T=250 lb-indiameter d=3.0 in and radiud…

Q: The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive…

A: A piston rod- Diameter d=20 mm, Length L=700 mm, Compressive force P =10 kN, End conditions- Guided…

Q: A solid cone of radius ro and vertex angle 20 is to rotate at an angular velocity w. The cone is…

A: Object: Solid coneDimensions: Radius: Vertex angle: 2θHousing: Present, with a gap between the…

Q: 5Q. The plate is moving at 0.6 mm/s when the force applied to the plate is 4 mN. If the surface area…

Q: A 30-m steel tape is suspended in the air between a theodolite a vertical rod, which is placed…

Q: A hydraulic press is used to compact powdered samples. The device is made of two interconnected…

A: Assume that the initial pressure in both piston was equal and equal to atmospheric pressure let FS…

Q: Medium oil having a sp.gr. of 0.90 flows through 120 mm diameter pipe with a mean velocity of 5.3…

A: Diameter of pipe, d = 120mm Mean velocity, Vav = 5.3m/sec The specific gravity of the soil, G = 0.90…

Q: A = Roll 16 kN/m' 6 m 4 6m + M = 96 kNm 4 m B = Pin

Q: The hollow shaft shown is made of a steel that is assumed to be elastoplastic with Ty= 145 MPa and…

A: Given,Yield shear stress, = 145 MPaModulus of rigidity, G = 77.2 GPaLength, L = 6m or 6000 mm

Q: Q2: Use dimensional analysis to derive an epresion for the power developed by an engine in terms of…

A: Given Power=P Torque=T Rotation speed=ω

Q: The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive…

A: Given data- Diameter d=20 mm, Length L=700 mm, Force P=10 kN, Young's modulus E=200 GPa, To Find-…

Q: 7. These are the minor losses EXCEPT: a. Sudden contraction b. Bends с. Valves d. Change in water…

A: 7. These are minor losses except d.change in water flow

Q: After being filled to a depth d with SAE 30 oil (SG = 0.91), a glass is placed to float in a tank of…

A: Depth upto which SAE oil is filled in a glass to make it float on water = d , Specific Gravity og…

Q: 2. The 9-kg paint stands on a wooden platform 1.2 kg in weight. Determine the magnitude and…

A: Given , Paint of 9kg stands on wooden platform of 1.2kg. Hence total downward acting weight…

Q: A solid cone of radius r and vertex angle 20 is to rotate at an angular velocity w. The cone is…

A: Object: Solid coneDimensions: Radius: Vertex angle: 2θHousing: Present, with a gap between the…

Q: Q- The surface area of a plate is 0.4 m² and its weight is 500 N which slides down on an inclined…

A: Given- Surface area A=0.4 m2Weight of plate W=500 NSpeed of sliding plate V= 4 m/sDynamic viscosity…

Q: 150-mm diameter Section A (a) 100-mm diameter 30° Section B

A: Energy is lost when it is changed from one form to another, transported from one location to…

Q: In a rotating cylinder test, the inner cylinder is of diameter 0.2 m and the outer cylinder of…

A: Given: Diameter of inner cylinder, D1 = 0.2 m Radius of inner cylinder, R1 = 0.2/2 = 0.1 m Diameter…

Q: Taking 'k' components 0. 77TEC + 0. 8TBD=1440. -(1) Taking 'j' components 0. 514TEC – 1.6TBD=0.….…

Q: A line was recorded as 1750.00 meters long. The standard tape weighs 0.65 kg , 30.00m long at 20°C…

A: Given, Lm = 1750 m M = 0.65 kg L = 30 m Ts = 20oC Ps = 50 N Tm = 5oC P = 75 N E = 200 GPa or…

Q: A 0.6 m square glass plate slides on a plane with a slope of 30° from the horizontal (Figure 1.2).…

A: Given: Slope of plane = 30 ° Weight of plate = 30N Area of plate = 0.6×0.6 Speed = 5cm/s Gap =…

Question

Determine the intensity of shear of an oil
having viscosity 2 poise. The oil is used for
lubricating the clearance between a shaft of
diameter 15 cm and its journal bearing. The
clearance is 2.5 mm and the shaft rotates at
150 rotation per minute.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The absolute viscosity of the liquid is 1.8 x 10^-3 Pa-s and its SG is 2.00. Compute the equivalent value in stokes
Please answer fast
I need the answer as soon as possible
Problem 6.2: The aluminum rod ABC (E=10.1x10° psi) (Figure 6.19), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E=29x10° psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation 28 kips 25 kips A D 12 in. -1.5 in. is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ksi. B - 2.25 in. 18 in. E Figure 6.19
An axial load of 900 KN is carried by a compound tube comprising of a steel tube and a brass tube. The internal and external diameter of the steel is 140 mm and 160 mm, respectively. While, the internal and external diameter of the brass tube is 160 mm and 180 mm, respectively. If the two tubes have the same length of 140mm, calculate the stresses and the load carried by each tube and the amount it shortens. Esteel = 2x10° N/mm? Ebrass = 1x10° N/mm?
Q1/ A liquid has a specific weight of 59 lb/ft³ and a dynamic viscosity of 2.75 lb-s/ft². Determine its kinematic viscosity.
A solid shaft is partially inserted in a hollow shaft where it snuggly fits and is rigidly attached on the wall of the hollow shaft. Consider the following: Solid shaft Torque, T = 9 kN-m Properties of the hollow shaft: Length = 4 m Outer diameter = 80 mm T Inner diameter = 40 mm Shear modulus = 96 GPa SECTION VIEW Hollow shaft Properties of the solid shaft: Length = 2.5 m Shear modulus = 112 GPa Embedment Length of embedment = 0.5 m A. What is the stress (MPa) of the hollow shaft at section A? B. What is the stress (MPa) of the solid shaft at section C? C. What is the stress (MPa) of the hollow shaft at section B? D. What is the stress (MPa) of the solid shaft at section B? E. What is the angle of twist (rad) of the entire assembly?
Determine the value of y.
Kerosene is placed inside a glass capillary tube having a radius of 0.5 mm. The kerosene inside the tube is measured to have a standing height of 59mm. Determine the true static height of the kerosene using a surface tension value of 0.035 N/m and Sg=0.8.
Rad the question carefully and give me right solution with clear calculations
Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (i) (ii) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. 20⁰ А μs=0.35 Figure Q2 B
The nutural frequancy for the system is equal to Ek rigid uniform bar of mass (m) P b 1 3kb²+PL 2n mL² the Answer is 1 3kb2 –3PL mL²