Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. Thecoefficient of static friction for the contact surfaces is 0.35.(i)(ii)Determine the mass value of block B when the impending motion of block A isdown the plane.Determine the mass value of block B when the impending motion of block A is upthe plane.20⁰Аμs=0.35Figure Q2B

Given:- The mass of the block A = 30 kg Block A is connected to block B The coefficient of static…

Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (1) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. (ii) 20⁰ प Hs = 0.35 Figure Q2 B

Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The coefficient of static friction for the contact surfaces is 0.35. (1) Determine the mass value of block B when the impending motion of block A is down the plane. Determine the mass value of block B when the impending motion of block A is up the plane. (ii) 20⁰ प Hs = 0.35 Figure Q2 B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: دلها ↓↓ P 7 B vwx What is the Reaction Force induced in the following system at point A, if? Wo = 7…

A: A beam is given we need to find out the reaction at A

Q: An A-36 steel tubular shaft is 1 m long and has an outer diameter of 40 mm. When it is rotating at…

Q: A bar AE is in equilibrium under the action of the five forces shown. Determine T (kN). F1 = 91 kN…

Q: The acrylic plastic rod is 300 mm long and 15 mm in diameter. If an axial load of 200 N is applied…

Q: A solid 0.61-in-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of…

A: ##Calculation of increase in temperature to cause the buckling of member #Bucking takes due to…

Q: The piston rod of diameter 20 mm and length 700 mm in hydraulic cylinder is subjected to compressive…

A: A piston rod- Diameter d=20 mm, Length L=700 mm, Compressive force P =10 kN, End conditions- Guided…

Q: 01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in. is…

A: Given that: For steel tube: Outside diameter, do=2.75 inWall thickness,…

Q: Problem No. 7 A hollow shaft that has 100 mm outside diameter and 80 mm inside diameter is used to…

Q: Two cast iron pipes are held together by a bolt as shown. The outer diameters of the two pipes are…

Q: of mass 10 kg and 7 kg respectively, are dined plane and released. The coefficients of tween the…

A: Draw free body diagram of blocks A and B as follows Consider the equilibrium of forces in the…

Q: A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper…

Q: The 62-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and…

A: Angle of twist = 0.0074 RadiansExplanation:Step 1: Step 2: Step 3: Step 4:

Q: A conductor with a specific gravity of 40.10-3 kg/m.mm2 was drawn between two poles, which are given…

A: Given values: Specific gravity, s = 40 * 10-3 kg/m.mm2 Tension, T = 10 kg/mm2

Q: A 364-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: Given data in question Load Coefficient of friction To find out Determine force P

Q: 3 ft 2 ft8 2 ft 12 kips The figure shows a homogeneous, rigid block weighing 12 kips that is…

Q: The wood block in (Figure 1) has a specific weight of 45 lb/ft³ = 62.4 lb/ft³. Take Po = 1.75…

A: Given data:Specific weight of wood block= 45lb/ft3Width of block =1 ft

Concept explainers

Design of structures using FEA

An arrangement, in which various members are interconnected with their constrained relative motion, the whole arrangement is then known as a structure. The degree of freedom of such a structure is zero. In such a structure, the load can act throughout the length of the structure or at the joints.

Question

Q2) Figure Q2 shows a 30-kg block is connected to block B through a frictionless pulley. The
coefficient of static friction for the contact surfaces is 0.35.
(i)
(ii)
Determine the mass value of block B when the impending motion of block A is
down the plane.
Determine the mass value of block B when the impending motion of block A is up
the plane.
20⁰
А
μs=0.35
Figure Q2
B

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

it seems like Iuv should be zero because xbar is zero distance away from the x-axis
A 3-in solid aluminum shaft is subjected to two torques as shown. Use G = 4 x 106 psi. Compute the maximum shearing stress and the angle of rotation at the free end. Answer: T = 1810.83 psi, 0 = 0.93⁰ 200 lb-ft 800 lb-ft 3 ft ·2 ft →
The motor shown in the figure produces a torque of 225 N·m in shaft (1). If the shear stress in shaft (1) must be limited to 56 MPa, determine the minimum acceptable diameter that may be used. Determine the magnitude of the internal torque in shaft (1). Assume that shaft (1) will have a solid circular cross section.
The coefficient of static friction between the block and the plane is 0.2, and between the rope and the drum D is 0.3. 1. What is the mass of 50 lb block in slugs? 2. Determine the maximum value of weight W which may be applied without causing the 50-lb block to slip. 3. Determine the minimum value of weight W which may be applied without causing the 50-lb block to slip. D 4. W
x= 137 y = 37 a = 6 b = 8 c = 1
4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)
I was wondering in the hydrodynamics how i can determine Cp in the pressure ressistance (coefficient pressure). so the total ressistance will be Rt= Rf+Rp. Given in Coefficients it will be: Ct=Cf+Cp now they say Cp in % of the friction coefficient (Cf). Ct=(1+k)*Cf with 1+k the formfactor. so the total ressistance will be Ct=Cd*1/2*ρ *v^2*S (wetted area m^2, v= velocity in m/s and ρ= 1025 kg/m3 for salt water) kan you explain me how to calculate the Cd in the total resisstance?
A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant. The torque delivered by the shaft is 3100 Ib-in. What horsepower must be delivered to the shaft to maintain a shaft speed of 630 rpm? What is the maximum shear stress developed in the shaft? Answer: P- hp T- psi
12. PLEASE ANSWER ASAP
Please provide solution and need drawing
A rigid block of mass m can be supported in each of the four ways shown. Each column consists of an aluminum tube that has a 44- mm outer diameter and a 4-mm wall thickness. Using E= 70 GPa and a factor of safety of 2.9, determine the allowable mass for each support condition. (Round the final answers to one decimal place.) m m DI 4 m (1) (2) The allowable mass for case (1) is The allowable mass for case (2) is The allowable mass for case (3) is The allowable mass for case (4) is m (3) kg. kg. kg. kg. m (4)
Please show the correcr solution