Two cast iron pipes are held together by a bolt as shown. The outer diameters of the two pipes are 50 mm and 70 mm and wall thickness of each pipe is 10 mm. The diameter of the bolt is 15 mm. The bolt broke while transmitting a torque of 2 kN-m. On what surface(s) did the bolt break? What was the average shear stress in the bolt on the surface where it broke?

Q: In the following structure, consider the following data: The connection at D is double and has a…

A:

Q: The steel shafts are connected together using a fillet weld as shown in the figure below. (Figure 1)…

A: Applied Torque= 63 N-m  Critical section is along a-a

Q: 22) One brass bar and one steel bar are forming the setup shown below. Determine the tresses and the…

A:

Q: A beam is loaded and supported as shown, where w1 600 Ib/n, w2 388 ft, a-3.7 ft, b 4.6 th, und e-…

A: F1 is the value of triangular load in region x = (0 to a)  So,  F1 = area of triangular loading

Q: The 50-mm diameter circular rod creates in the metal sheet a shear stress through section AC and BD.…

A:

Q: A 60-inch length of 2-inch OD x 1/8-inch wall 2014-T4 aluminum tube is supported by pinned supports…

A:

Q: In the bolted connection as shown in the figure, assuming that the applied load is uniformly…

A:

Q: A flanged bolt coupling consists of ten 16-mm-diameter bolts spaced evenly around a bolt circle 650…

A: Given data,    No of bolts = 10 Diameter of bolt (d) = 16 mm Diameter of bolt circle = 0.650 m…

Q: Assume that two 8-mm-diameter bolt joins the plates that are each 175 mm wide. The allowable…

A: Given, 2-8 mm diameter bolt width of plate= 175 mm Allowable bearing stress for plate=120 MPa…

Q: The rigid bar abcd supports point loads At A and D and is being supported by two bars at B and C.…

A:

Q: The copper pipe has outer and inner diameters of 2.5 in and 2.0 in. If it is tightly secured to the…

A:

Q: A solid shaft of circular cross-section is subjected to torque Twhich produces a maximum shear…

A:

Q: For the shaft loaded as shown, which point(s) at the section shown experiences the maximum shear…

A: Let's draw the FBD  for first figure At the L shaft observe the stresses and their directions…

Q: Consider two shafts one solid of mild steel of 200 mm diameter and another hollow of alloy steel of…

A: The diameter of the solid shaft is 200 millimeters.The outer diameter of the hollow shaft is 200…

Q: The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to…

A:

Q: Two square rods AB and BC are welded together at B and loaded as shown. Determine the average normal…

A:

Q: 20MPA a In Figure , according to the stress condition of a stack of I-section beam. (30Mpa is the…

A: Principal stress=σx+σy2±σx-σy22+ζ2=40+-202±40-(-20)22+302=10±42.42 MpaThus σp1=52.42Mpa and…

Q: P 100 mm 10 mm 10 mm P

A: As per bartleby guidelines the given data closely related to the IS code provisions also the term…

Q: QI: Find the normal stresses at sections A-A, B-B, C-C, and, D-D for the body as shown in figure…

A: As per guidelines we are supposed to answer only first question

Q: Exam A solid shaft of circular cross-section is subjected to torque 7 which produces a maximum shear…

A:

Q: Consider two shafts one solid of mild steel of 200 mm diameter and another hollow of alloy steel of…

A: The diameter of the solid shaft is 200 millimeters.The outer diameter of the hollow shaft is 200…

Q: A flat steel bar, 26 mm wide by 4 mm thick and 1.8 m long, is bent by couples applied at the ends so…

A:

Q: Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt…

A: We have to find out the unit stress in each bolt with the given data,

Q: Question 1 [Soalan 1] Members AB and AC support the 100 kg crate. Determine the tensile force…

A:

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A:

Q: A 6-inch diameter pulley mounted on a 2-inch shaft as shown below transmits 9 kW at 1000 rpm. What…

A: Given: The diameter of the pulley is 6 in. The diameter of the shaft is 2 in. The power transmits is…

Q: A flat steel bar, 25 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A: Here, we have used two formulae 1. Max deflection at mid point due to couple at end…

Q: Home work The copper pipe has an outer diameter of 40mm and an inner diameter of 37mm. If it is…

A:

Q: two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm.…

A: Find modular ratio:n=EwEs=40200=15so,Reduced width of wood =1505=30mmFInd…

Q: 100 MPa 60 MPa 150 MPa 150 MPa 60 MPa 100 MPa

A:

Q: 1. The solid aluminum shaft ABCD caries the three torques shown. (a) Determine the smallest safe…

A:

Q: The boiler has an inside diameter of 60.0 in. and a wall thickness of 1.000 in., and it is made of…

A:

Q: Question 2 300 mm 20 mm -200 mm- ta 200 mm Section a-a 20 mm The maximum allowable tensile strength…

A:

Q: A compound tube consists of a steel tube 150 mm internal diameter and 170 mm external diameter and a…

A:

Q: 40KN The beam, having the cross-section «I», is 60kNm subjected to a loading as shown in the figure.…

A: Any Beam or structure under the application of loading shows the bending deformations due to that…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.