In the bolted connection as shown in the figure, assuming that the applied load is uniformly distributed among the three rivets whose diameter is 12 mm inserted on a 12.5 mm diameter hole, determine the shearing stress in the rivet P=40 KN 120 mm P-40KN P=40KN P=40KN 10 mm 10 mm

In the bolted connection as shown in the figure, assuming that the applied load is uniformly distributed among the three rivets whose diameter is 12 mm inserted on a 12.5 mm diameter hole, determine the shearing stress in the rivet P=40 KN 120 mm P-40KN P=40KN P=40KN 10 mm 10 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following gives the maximum bearing stress among all the plates? A.1.50 P/bt B.1.50 P/nd2 0.75P- C.0.75 P/bt 1.5P D.0.750 P/id2 0.75P- For the deformed plate shown in figure X, the magnitude of the shear strain at point D is nearest to 2 mm 5 mm A.0.229 rad B.0.004 rad C.0.573 rad D.0.010 rad 500 mm 500 mm Plates A and B are to be connected using bolts and two cover plates C and D as shown. The force exerted on plate A is 30 kN and the diameter of the bolts used is 25 mm. The thickness of all the plates is 15 mm. Which of the following is the shear stress experienced by either bolt? A.30.6 MPa F B.61.1 MPa B C.45.8 MPa D.15.3 MPa B
A solid brass E= 100 GPa axial member is loaded and supported as shown in the figure. Segments (1) and (2) cach have a diameter of 22 mm and segment (3) has a diameter of 14 mm. Carrying loads W1 - 37 kN, W2 = 14 kN, and W3 = 25 kN, at their respective positions shown on the figure below. Determine the deformation of segment (2) in MPa. Answer should be rounded up to the nearest 3 decimal places. (1) WI W2 W3
(a) (b) (c) Given, (i) area of Z100 x 100 x 8 = 15.39 cm2, %3D (ii) thickness of gusset plate = 10 mm (iii) nominal diameter of rivets = 16 mm, %3D (iv) permissible tensile stress = 150 MPa, and (v) as per IS : 800 (1984) for single angle, the net effective area = A, + KA, %3D ЗА, K = (3A, + A2) where, A, = effective cross-sectional area of the connected leg, the gross cross-sectional area of the A2 %3D unconnected leg
In the figure shown, determine the normal stresses at AD + and BC • shearing stress at bolt D + , bearing stress of AD at bolt D bearing stress of member EDC at bolt D All bolts Ø16mm 04 n 0.25 m 02 m |D 20kN E 10 x 50 mm 8 × 36 mm
A bracket has been loaded as shown in figure. Compute the top and bottom fibre stress at section A-B
PROBLEM 4: The figure shows a plate that is fastened to a fixed to a fixed member by five 12-mm- diameter rivets. Compute the value of the loads P so that the shearing stress in any rivet does not exceed 79 MPa. 122 mm 40 mm 40 mm 102 mm -122 mm Figure 4
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
jp
Determine the shear lag factor of the connection shown in the figure.
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
I need the answer as soon as possible