A EQA 150 x 150 x 15 is used as a tension member and is connected to 8 mm gusset plates. S275 steel is used for tension member and the gusset plate. The member has been designed to resist a tension factored load Nt,Ed= 80.10 KN. Use full thread bolts M10 5.8 bolts in two lines, 4 bolts in each line. Design the tension member and the bearing type connection.

A EQA 150 x 150 x 15 is used as a tension member and is connected to 8 mm gusset plates. S275 steel is used for tension member and the gusset plate. The member has been designed to resist a tension factored load Nt,Ed= 80.10 KN. Use full thread bolts M10 5.8 bolts in two lines, 4 bolts in each line. Design the tension member and the bearing type connection.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Select a single-angle tension member of A36 steel to resist the following service loads: dead load = 225 KN, live load = 450 kN, and wind load = 200 KN. The member will be connected through one leg with 25 mm diameter bolts in two lines. There will be four bolts in each line. The member length is 6m. a. Use LRFD. b. Use ASD. Bolt lines
A double-angle shape, 2L7×4×3/s , is used as a tension member. The two angles are connected to a gusset plate with 7/8-inch- diameter bolts through the 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used. a. Compute the design strength. b. Compute the allowable strength. 2/2" 7" 3" 1/2" 2L7 × 4 × 3/s FIGURE P3.4-5
A staggered connection is shown in the figure. Using LRFD & ASD, determine the maximum tensile force that the plate could carry. Assume A36 steel (Fy = 248 MPa, Fu = 400OMPA). Use NSCP 2015 provisions. For Plate: t = 12 mm, width = 350 mm For Rivet: Diameter = 20 mm 70 100 70 80 70
- Bolt lines Seleet a single-angle tension member of A36 stee to resist the following service loads: dead load - 220 kN, live load - 440 kN, and wind load - 200 kN. The member will be connected through one leg with 25-mm diameter bolts in two lines. There will be four bolts in each line. a. Use ASD b. Use LRFD 3.
Problem 1: A butt joint shown in Figure ST – 127 using A325 bolts with a diameter of 16 mm with threads excluded in a shear plane. The plate used is A36 steel with Fy = 400 MPa. Use LRFD. Hole diameter is 3 mm larger than the bolt diameter. 1. Compute the design strength Pu of the connection based on bearing of the plate. Hint: The inner plate will govern. No need of checking the outer plate. 2. Compute the design strength Pu of the connection based on bolt shear. Hint: the bolt is in double shear. As is times 2 for every bolt. |32 84 84 12.5 mm T/2 T/2 22 mm 12.5 mm T/2- T/2 + T 180 mm Figure ST - 127
SOLVE FOR1 HR
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
column section =ISEB500 bracket plate thickness=11mm p=450KN E=270mm p=5mm bolt size =M20
4. from the preceding problem, determine the ultimate tensile force Pu that the bolted connection could carry against tensile rupture in the net section. Use A-50 steel and LRFD.