A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. a) Determine the allowable tensile strength for ASD. b) Determine the design tensile strength for LRFD.

A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. a) Determine the allowable tensile strength for ASD. b) Determine the design tensile strength for LRFD.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate…

A: Given:- Thickness of plate, t=16 mmDiameter of bolts, d=22 mmNumber of bolts, n=6S1=40 mmS2=80…

Q: 2.10 A square yellow it is subjected t the allowable t mum allowable cross section if

Q: 60 b P P 150 100 100 100

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and th 4-inch-diameter bolts. Assume…

Q: A steel angle is bolted to a gusset plate with three 20 mm diameter bolts, as shown in the figure.…

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

Q: What will be the block shear strength of a tension member as shown in figure below? The steel is of…

Q: A PL ½ x 8 tension member is connected with six 1-inch diameter bolts as shown in the figure below.…

A: Answer We are given Plate 1/2 x 8 bolt diameter = 1 in A36 steel Shear lag factor U = 0.1

Q: Determine the tensile strength of the welded A992 WT4×20. WT4 × 20 PL - Transverse weld

A: Given:- The steel section used = WT 4×20 The steel used = A992 To determine:- The tensile strength…

Q: The splicec connected 248 MPa сес CO

Q: in steel, explain effective length factors

A: Effective length factors (K-factor) are used in the analysis and design of steel structures to…

Q: allowable

A: Block shear strength Agv =12in2×4 in= 4.00 in2Agv = 4.00 in2Ant = 12in10in = 5.0 in2Ubs = 1.0Rn…

Q: O Based on bolt capacity in shear. O Based on bolt bearing capacity. ® Based on block shear strength…

Q: ISA 75 x 75 x 8 mm serves as tensile member. This angle is welded to a gusset plate as shown in…

A: Note : This question is related to Indian Standard Code as asked in the problem. Given data, ISA…

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: bolted lap joint

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75…

A: We will use formula of Net area.

Q: Found solutions, steel structure

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g =…

A: Given data in question Thickness of plate Diameter of bolt Bolt lines Guage distance To find out…

Q: The area of the double angle shown is Ag = 5.6 in2. Each angle has a thickness t = 0.25 in. Given U…

A: Double Angle Tension Member Total Gross Area, Ag=5.6 in2 Thickness of angle, t=0.25 in Reduction…

Q: Material Strengths: Fy = 248 MPa, Fu = 400 M Pa For the two lines of bolt holes, the pitch is the…

Q: Find the lim f6atx) -f(9) for fCx) = Jx - 3

Q: 2. The figure shows a plate having a width of 400mm and thickness of 12mm is to be connected to…

Q: The angle shown in the figure is L 7 X4 X 7/16. Steel used is AS72 Gr. 55 steel. Diameter of bolts…

A: diameter of bolt = 1.125inch distance between two bolts=3inchs Ag=4,62in2 by steel table fy =70ksi…

Q: A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572…

A: Tensile capacity, the maximum load that a material can support without damage when being determined…

Q: determine: (a) the elastic section modulus and the yield moment. (b) the plastic section modulus…

A: fy = 345 MPaDeterminea. Elastic modulus of section and yield moment. b. Plastic modulus of section…

Q: A butt joint shown in figure 3.29 is bolted using A 325 bolts with a diameter of 22 mm, with threads…

Q: With the dimensions already given, determine the allowable value of the tensile load P, considering…

A: Answer (1) Allowable normal stress at the two vertical bolts (1) and 92) is 160 Mpa Allowable…

Q: A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter…

A: Double angle section is shown in the figure above. Grade 60 steel is used. Diameter of bolts= 1/2…

Q: Determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi, Fu=58ksi…

A: Yield Strength : Yield strength is a maximum stress a structure can bear beyond the maximum stress…

Q: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

A: The bracket shown in the figure is supported by four 22 mm diameter bolts in single shear. The…

Q: The spliced joint of the bottom chord in a bridge truss shown in the figure below is connected with…

Q: A structural tee bracket is attached to a column flange with six bolts as shown in Figure . All…

A: Solution

Q: Bolted Connections hear lap connection

A: Single Shear Lap Connection: 22 mm bolts Fnv = 300 MPa Bolts are in Single Shear Number of bolts = 6…

Q: Name the parts shown on the bolted joint element below, respectively. 3 Grip- washer - threads Head…

Question

A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An.
a) Determine the allowable tensile strength for ASD.
b) Determine the design tensile strength for LRFD.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What will be the tensile strength due to rupture of critical section of an angle section ISA 150 × 115 x 8, which is connected to gusset plate as shown in figure?. Use Fe410 grade steel. 150 mm 115 mm 8 mm 8 mm 60 mm 150 mm
.
Centroid + Inertia 200 x 20 mm Plate The strength of the rolled section shown is increased by combining S section, channel, plate and then welded. 1. Determine the location of its centroid; and 5310 x 47.3 C310 x 30.8 2. Determine the moments of inertia of the composite section with respect to its centroidal x and y Semi-circle Weld, 10mm radius axes.
Please solve the following problem is ksi
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem The butt connection shows 8-22 mm dia. A325 bolts spaced as follows: S1 = 40 mm S3 = 50 mm t1 = 16 mm S2 = 80 mm S4 = 100 mm t2 = 12 mm Steel strength and stresses are: Fy = 248 MPa Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Bolt Hole diameter = 25 mm Questions: Calculate the allowable tensile load T, under the following conditions. a) Based on the gross area of the plate b) Based on the net area of the plate c) Based on block shear strength
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Determine the allowable strength of the figure as shown
Determine the load capacity of the angle LRFD. USE NSCP 2015.
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear