Select a single-angle tension member of A36 steel to resist the following service loads: dead load = 225 KN, live load = 450 kN, and wind load = 200 KN. The member will be connected through one leg with 25 mm diameter bolts in two lines. There will be four bolts in each line. The member length is 6m. a. Use LRFD. b. Use ASD. # Bolt lines

Select a single-angle tension member of A36 steel to resist the following service loads: dead load = 225 KN, live load = 450 kN, and wind load = 200 KN. The member will be connected through one leg with 25 mm diameter bolts in two lines. There will be four bolts in each line. The member length is 6m. a. Use LRFD. b. Use ASD. # Bolt lines

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: ✓ Ultimate tensile strength of each member CD is 300 ksi Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in: C and D-2 in E and F - 1 in. 1.5 in. thick Support Plates -2 ft + D 3 ft B 2 in thick Support Mate Solution Step 1. Identify the conditions for design. Stress normal stress in each member CD, OCD shear stress in bolt A, TA shear stress in bolt C, T shear stress in bolt E, T shear stress in bolt F, T bearing stress on member BDE due to: bolt B, BDE-B bolt D, OBDE-D bolt E, OBDE-E bearing stress on support plates at…
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
PLEASE DOUBLE CHECK YOUR ANSWER Determine the maximum factored load that can be applied to the Tension member shown. The angle is ASTM A36. The diameter of the bolts is 1-in. CIVIL ENGINEERING STEEL DESIGN W12 x 16 4,-0.220 in -3.99 in 1=+=+=+= 3 in 3 in 3 in
SOLVE FOR1 HR
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
A PL40 mm X 250 mm (smaller member) is connected to a gusset plate (bigger member) as shown. The diameter of the holes are 25 mm. The pitch and gage of the holes are 50 mm and 75 mm, respectively. The yield strength of the steel is 260 MPa while the ultimate tensile strength of the steel is 400 MPa. Determine the design (LRFD) tensile strength of the tension member in kN. Neglect block shear. H FO E. • D A В
P4.002 Three bolts are used in the connection shown in the figure. The thickness of plate (1) is 15 mm. The ultimate shear strength of the bolts is 350 MPa, and the ultimate bearing strength of plate (1) is 375 MPa. Determine the minimum bolt diameter required to support an applied load of P = 155 kN if a minimum factor of safety of 2.8 is required with respect to both bolt shear and plate bearing failure. Answer: dbolt min = (1) mm
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld