A double storey reinforced concrete restaurant will be built near the beach in Batu Layar, Johor. Based on design life of 100 years with 1 hour and 30 minutes fire resistance, determine the suitable concrete grade and concrete cover for the continuous edge beams of the building to satisfy the requirements for bond, durability. and fire resistance. The cross-section of the beam is shown in FIGURE QI.

A double storey reinforced concrete restaurant will be built near the beach in Batu Layar, Johor. Based on design life of 100 years with 1 hour and 30 minutes fire resistance, determine the suitable concrete grade and concrete cover for the continuous edge beams of the building to satisfy the requirements for bond, durability. and fire resistance. The cross-section of the beam is shown in FIGURE QI.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question Number (2c) Civil Engineering Materials
7. Which of the following gives the x of the composite figure a. 54.8 mm ? Fig 1 b. 50.6 mm c. 48.2 mm 120 mm d. None of the above 60 mm 40 mm 8. Which of the following gives the y of the ? Fig 1 80 mm composite figure a. 36.6 mm b. 45.2 mm c. 34.8 mm 60 mm d. None of the above Figure 1
IMAGMAMA What is the working moment of resistance for a beam of width 300 mm and effective depth 450 mm having tension reinforcement 3 - 25 mm dia bars of Fe415 and concrete of Grade M25?
Design strength for M25 concrete in direct compression, bending compression and flexural tension are, respectively A 10 MPa, 11.15 MPa and 3.5 MPa B 25 MPa, 11.15 MPa and 3 MPa с 10 MPa, 12.5 MPa and 3.5 MPa D 25 MPa, 11.15 MPa and 2.57 MPa
Plz, solve this problem in all its parts. Reinforced Concrete Design-1 Follow ACI Code (American Concrete Institute) Last two digits of Registraion Number: 95 A simply supported beam having span length of 24′ and cross-section of 15" × 21"is subjected to an ultimate load of ?? k/ft. Taking ?c = 3??? and ?y = 60???, a) Calculate the amount of reinforcement required for a given beam section to fail under balanced condition.b) Determine the magnitude of strain developed in the tension steel at the ultimate stage if the magnitude of ?? = (?/10) k/ft. Where ? = Last two digits of Registration Number
The 5-story building design project will have its beams and slab poured monolithically and formed a T- section as shown. Determine the design strength pMn in accordance with the ACI/NSCP Code. The tension steel is 9- 36 mm diameter bars (As of 36 mm = 1006 mm2) with three bars in each of three layers. Assume 12 mm stirrups are used, and there is 25 mm between layers. Use fc': 28 MPa and fy = 413.70 MPa. 750 mm T175 mm 1000 mm 9-36 mm diameter bars 350 mm
Concrete
Beams that are part of the seismic force resisting system (concrete moment frames) often have about the same reinforcing at the top and bottom of the beam because: Question 1 options: earthquake forces can load the building in any horizontal direction the top reinforcement helps to confine the concrete when subjected to earthquake forces the "balanced" reinforcing distributes earthquake forces more evenly the added reinforcing steel gives the beam significant additional strength
With how many pounds of concrete (specific weight=24 kN/m3) must a beam of the volume of 0.2 m3 and s.g.=0.33 be coated to ensure that it sinks in water?
A flexure strength tests were performed on a concrete beam having a cross section of 0.15x0.15m and a span of 0.45m. If the total load at failure was 37.5kN, calculate the ff:a. The flexure strength of the concrete if center-point was applied.b. The flexure strength of the concrete if third-point was applied.c. Which of the two flexural tests is recommended in determining the flexure strength of the concrete and why?
4. Please describe the requirements for the concrete transportation.
Subject: Composite Structure What is concrete filled steel tube (CFST)? Describe the basic mechanical behaviour of CFST. The proper cases for buildings with CFST. Examples for bridges with CFST