A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm thickness as shown in the figure. There are twelve power driven rivets of 20 mm diameter at a pitch of 50 mm in both directions on either side of the plate. Two cover plates of 10 mm thickness are used. The capacity of the joint in tension considering bearing and shear only, with

A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm thickness as shown in the figure. There are twelve power driven rivets of 20 mm diameter at a pitch of 50 mm in both directions on either side of the plate. Two cover plates of 10 mm thickness are used. The capacity of the joint in tension considering bearing and shear only, with

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following steel circular bar (Es = 200 GPa) is divided into two segments. Segment 1 is tubular and segment 2 is solid. Determine the distance "x" so that the bar does not exceed a total deformation of 2.5 mm. The load P is equal to 25 kN, the diameter d is equal to 30 mm, and the length L is equal to 10 m.
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
From the Truss member shown, design all the tension members for ASD and LRFD, if the connection for the angle bars are shown. Use A36 STEEL. 100 mm 150 mm E F 2.5 m B SERVICE DEAD LOAD =300 KN SERVICE LIVE LOAD = 200 KN 2 m 2 m 2 m 2 m
2) The angle member is connected to the W section member by 4-19 mm diameter bolts as shown in the figure. Determine the largest safe value of Pif the shearing stress in the bolts is not to exceed 70 MPa and bearing stress in the plates is not to exceed 120 MPa. The thickness of gusset plate is 10mm. 30° O
A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is supported by bolts at A and B that are in the single shear. The bar is loaded by 4kn at point D. Determine the minimum diameter of the bolt at B if the allowable shear stress is 120 mpA
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75 12 mm P. mm O. O 300 mm 40 80
A steel beam is bolted to a steel girder by a connection similar to that in the figure shown below. The diameter of the bolt is 10 mm, and the thickness of each angle bar is 4 mm. For each bolt, assume that the allowable bearing stress is 224 MPa. Find the allowable load in kN on the connection. Assume the thickness of the web of the beam to be 7 mm and the thickness of the web of the girder to be 8 mm The final answer should include two decimal places
Explain please
I NEED ANSWER
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
IDENTIFY THE ZFM ZERO FORCE MEMBERS
The single shear connection consists of six 26-mm-diameter bolts. If the ultimage strength of the bolts is 720 MPa, determine the factor of safety for the connection at an applied load of P= 570 kN. P=570 kN