Please answer Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joinedtogether by a pin with a diameter of 60 mm.200 mm60 тmP160 тmT 35 mm35 mm200 mm1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearingstrength of the plate is 250 MPa and the shear strength of the pin is 100 MPa.kN

Answered: Image /qna-images/answer/513bd366-14a8-4dca-a148-57fde0627e50.jpg

Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of 60 mm. 200 mm 60 тm P P 160 тm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 MPa and the shear strength of the pin is 100 MPa. kN

Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a pin with a diameter of 60 mm. 200 mm 60 тm P P 160 тm T 35 mm 35 mm 200 mm 1) For a Factor of Safety of 2, find the maximum load P that can be applied if the bearing strength of the plate is 250 MPa and the shear strength of the pin is 100 MPa. kN

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.8.1P: Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.

See similar textbooks

Similar questions

KINDLY ANSWER IN CLEAR EXPLANATION.
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
KINDLY DRAW THE FREE DIAGRAM AND ANSWER
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
Two bolts are used to lap points two steel plates. Tensile force on the plate is 45kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.0
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
I need the answer as soon as possible
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft in MPa. ( COMPLETE SOLUTION NO ROUNDING OFF)