Answered: A cylindrical specimen of a cold-worked…

A cylindrical specimen of a cold-worked brass has a ductility (%EL) of 22%. If its cold-worked radius is 12 mm, what was its radius before deformation? You may need to use Animated Figure 7.19c. i mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8)
A mild steel specimen originally 300 mm long is pulled in tension with a stress of 500 MPa. If the deformation is entirely elastic, calculate the resultant elongation? The modulus of elasticity of steel is 200 GPa.
A cylindrical metal specimen having an original diameter of 10.63 mm and gauge length of 50.1 mm is pulled in tension until fracture occurs. The diameter at the point of fracture is 7.60 mm, and the fractured gauge length is 74.5 mm. Calculate the ductility in terms of (a) percent reduction in area (percent RA), and (b) percent elongation (percent EL). (a) i percent RA (b) i percent EL
A copper rod with a diameter of 24 mm is subjected to tension within the elastic region. If themodulus of elasticity is 115 GPa and a Poisson’s ratio of 0.34. Determine the force that willproduce a reduction of 0.003 mm in the diameter.
Please answer d,e,f
Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels. Utilizing the data given answer the three queries given below. Material Yield Tensile Strain at Fracture Elastic StrengthStrengthFractureStrengthModulus (MPa) (MPa) (MPa) (GPa) A 410 1440 0.63 265 410 В 200 220 0.40 105 250 C 815 950 0.25 500 610 D 800 650 0.14 720 210 E Fractures before yielding 650 550 1) Which will experience the greatest percent reduction in area? Why? 2) Which is the strongest? Why? 3) Which is the stiffest? Why?
Please present FBD/s A tensile test is performed on a brass specimen 10mm in diameter using a gage lenght of 50mm. When the tensile load P reaches a valule of 20kN, the distance between the gage marks has increased by 0.122mm. What is the modulus of elasticitiy of the brass?
1. The tensile strength vs. temperature curves of aluminum are plotted below. Explain the meaning of these two curves. 400 Ultimate strength 300 Yield strength 200 100 -200 -150 -100 -50 50 100 150 200 250 Temperature, °C Strength, kPa
The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0 04 0.08 0.12 0.16 0.20 0.24 0.28 0 0005 0.0010.0015 0.002 0.0025 0.0030.0035
(a) the modulus of elasticity in GPa for the Aluminum B) the proportional limit in MPa for the Aluminum C) the ultimate strength in MPa for the Aluminum D) Ductility of material based on percent elongation
Given your understanding of what initiates and controls failure in materials, which of the following will increase the failure strength or lifetime of a test piece or component and why? a. Decreasing the difference between the maximum and minimum stress values, as this effects the stress concentration factor b. Decreasing the temperature below the brittle-ductile transition temperature, to make it harder C. Polishing to reduce surface defects Od. Increasing its volume, to give a larger cross sectional area Oe. Increasing the grain size so there are less grain boundaries to initiate failure
A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a Poisson's ratio of 0.35 is pulled in tension with force of 40,000 N. If the deformation is totally elastic, what is the strain experienced by the specimen? O 0.00463 O 0.00116 O 0.0029 O 0.01350