A cylindrical specimen of cold-worked steel has a Brinell hardness of 240. If the specimen remained cylindrical during deformation and tensile strength on percent cold its original radius was 11.8 mm, determine its radius after deformation. For steel, the dependence work is shown in Animated Figure 7.19b. mm

A cylindrical specimen of cold-worked steel has a Brinell hardness of 240. If the specimen remained cylindrical during deformation and tensile strength on percent cold its original radius was 11.8 mm, determine its radius after deformation. For steel, the dependence work is shown in Animated Figure 7.19b. mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A Brinell hardness tester with a diameter of 10 mm and a load of 500 kg gives an impression with a diameter of 1.62 mm in a steel alloy. Calculate the Brinell hardness (HB) in the steel alloy
an isotropic materials, the relationship between the Young's modulus (E), shear modulus (G) and Poisson's ratio (µ) is given by For
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 32 mm, d1 = 117 mm, b2 = 19 mm, d2 = 19 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 13 MPa, and the allowable compressive bending stress is 13 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a M | A В
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; α=α=12.5 x 10-6/°F] bar with a width of 2.5 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; α=α=9.6 x 10-6/°F] bar with a width of 1.7 in. and a thickness of 0.75 in. The supports at A and C are rigid. Assume h1=2.5 in., h2=1.7 in., L1=31 in., L2=46 in., and Δ=Δ= 0.04 in. (A) Determine the lowest temperature, Tcontact, at which the two bars contact each other. (B) Find a geometry-of-deformation relationship for the case in which the gap is closed. Express this relationship by entering the sum δ1+δ2, where δ1 is the axial deflection of Bar (1), and δ2 is the axial deflection of Bar (2). δ1+δ2= _____in. (C) Find the force in the Bar (1), F1, and the force in Bar (2), F2, at a temperature of 225oF. By convention, a tension force is positive and a compression force is negative. IN KIPS (D) Find σ1 and σ2,…
Q.1 The yield stresses (oy) have been measured using steel and aluminum specimens of various grain sizes, as follows: Material D (µm) σΥ (MPa) Steel 60.5 160 136 128 Aluminum 11.1 235 100 223 (a) Determine the coefficients o and kỵ in the Hall- Petch for these two materials. (b) Determine the yield stress in each material for a grain size of d=26 um.
For a point on a steel specimen, the principal stresses are known to be 01 = 360 MPa and O2 = 60 MPa. Calculate the minimum yield stress of the material according to the Tresca criterion. Give your answer in MPa to 3 significant figures.
The following shaft is composed of two materials, both rigidly bonded. The data is provided in the table: Determine: The maximum torque that can be applied based on the maximum stresses of each material. The total deformation of the shaft with the torque from the previous section. The maximum torque that can be applied if the maximum deformation of the shaft is 2.50 rad.
Engineering strain of a mild steel sample is recorded as 0.100%. The true strain is 1. 2. 3. 4. 0.010% 0.055% 0.099% 0.101%
A cylindrical specimen of undeformed brass that has a diameter of 300 mm is elastically deformed to a tensile strain of 0.001. If the Poisson's ratio for this brass is O.35, what is the change in specimen diameter? O Decrease by 3.00 x 104 m O Decrease by 1.05 x 104 m O Increase by 1.05 x 104 m O Increase by 0.028 mm
At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C
A single zinc crystal is loaded in tension with the normal to its slip plane at 60° to the tensile axis and the slip direction at 40° to the tensile axis. a) Calculate the resolved shear stress when a tensile stress of0.69 MPa is applied. b) What tensile stress is necessary to reach the critical resolved shear stress of 0.94 MPa?
A steel plate used for polymer forming is to be bent into a circular shape having an inside radius of 10 m. What maximum thickness can be used for the plate if the normal stress is not to exceed 267 MPa? Assume that the modulus of elasticity for the steel is 201 GPa.