The following figure shows the tensile stress-strain curve for a plain-carbon steel.60080500MPa60010 psi608040040060-300404020020020201000.0050.050.100.15Strain(a) What is this alloy's tensile strength?MPа(b) What is its modulus of elasticity?GPa(c) What is the yield strength?iMPaStress (MPa)Stress (10 psi)

The following figure shows the tensile stress-strain curve for a plain-carbon steel. 600 80 500 MPa 600 10 psi 80 60 400 400 60 300 40 40 200 200 20 20 100 to.dos 0.05 0.10 0.15 Stra in (a) What is this alloy's tensile strength? i MPa (b) What is its modulus of elasticity? GPa (c) What is the yield strength? MPa Stress (MPa) (Isd 0t) ssens

The following figure shows the tensile stress-strain curve for a plain-carbon steel. 600 80 500 MPa 600 10 psi 80 60 400 400 60 300 40 40 200 200 20 20 100 to.dos 0.05 0.10 0.15 Stra in (a) What is this alloy's tensile strength? i MPa (b) What is its modulus of elasticity? GPa (c) What is the yield strength? MPa Stress (MPa) (Isd 0t) ssens

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a Poisson's ratio of 0.35 is pulled in tension with force of 40,000 N. If the deformation is totally elastic, what is the strain experienced by the specimen? O 0.00463 O 0.00116 O 0.0029 O 0.01350
#2 will upvote to anyone who will answer
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa Allowable compressive stress 140 MPa 70 MPa If the allowable strain for both materials is 0.0005, which of the following most nearly gives the maximum load the member can carry so that this allowable strain is not exceeded? Select the correct response 162.00 kN 185.00 kN 205.00 kN 175.00 kN
Getting measurements from Figure , determine approximate values of the following items for steel with different carbon contents. Use one system of units only as specified by the instructor.a. Yield stressb. Ultimate strengthc. Strain at failured. Effect on modulus of elasticitye. Approximate toughness. Curves may be approximated with a series of straight lines.f. Comment on the effect of increasing carbon content on items a through e above.
A steel bar has a length of 2.5 m and cross-section of 200-mm x 100-mm. The modulus of elasticity of this material is 210 GPa and Poison's Ratio is 0.3. The change in width after applying a tensile force of 150 kN is?
I need the answer as soon as possible
If a steel column with cross-sectional area A = 1000 mm2, modulus of elasticity E 200 MPa and length of 10 m is subjected to 2 kN axial tension, compute for its axial deformation O + 100 mm O +0.1 mm O 100 mm O-1.0 m
Determine the ductility of the following steel samples that undergo tensile strength test. All dimensions in millimeter.