A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 128 mm and a wall thickness of 16 mm. The shaft is subjected to torques Tg = 41 kN-m and Tc = 18 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). (1) 63.9 MPa 83.0 MPa 88.8 MPa 69.9 MPa O 52.2 MPa TB B Tc C X

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 128 mm and a wall thickness of 16 mm. The shaft is subjected to torques Tg = 41 kN-m and Tc = 18 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). (1) 63.9 MPa 83.0 MPa 88.8 MPa 69.9 MPa O 52.2 MPa TB B Tc C X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 236 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 120 mm and a wall thickness of 16 mm. The shaft is subjected to torques TB = 44 kN-m and TC = 16 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2).
A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which has a diameter of 2.2 in. The shaft is subjected to a tensile axial load of P = 14 kips and torques TA = 5 kip·in. and TB = 34 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A compound shaft consists of segment (1), which has a diameter of 1.0 in., and segment (2), which has a diameter of 1.3 in. The shaft is subjected to a tensile axial load of P = 16 kips and torques TA = 14 kip·in. and TB = 32 kip·in., which act in the directions shown. Determine the normal and shear stresses at (a) point H and (b) point K. For each point, show the stresses on a stress element.
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 226 mm and a wall thickness of 8 mm. Segment (2) has an outside diameter of 128 mm and a wall thickness of 14 mm. The shaft is subjected to torques TB = 48 kN-m and TC = 17 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (1).
3. The closed tube shown in Fig. 3 has two square cells, each 100 mm on a side, and a semicircular cell. Thickness dimensions are all in millimeters. A torque of 2(10) N.mm is applied. Let G =77 GPa. Find the shear stresses and rate of twist (angle of twist per unit length). Neglect stress concentrations. 0.3 0.3 0.3 0.5 10 0.3 0.3. 0.25 0.4 Ans.; q₁ = 28.7 N/mm, 92 = 46.9 N/mm, 93 = 41.8 N/mm,
For the two-shaft shown below, rank each point (1, 2, 3, 4) on the cross-sectional areas in terms of shear stress. Both shafts are subjected to the same torque T. Shaft A has a radius of 4 cm. Shaft B is a hallow shaft that has an outer radius of 8 cm and inner radius of 5 cm. 4 1 2. 5 cm 8 cm 1 cm 4 cm Shaft A: solid shaft Shaft B: hallow shaft
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If the shaft is made from a material having an allowable shear stress of Tallow = 70MP , determine the maximum value for P Figure 1 of 1 1m 1m 1 m 30 mm 40 mm
(b) A cooling tube having the cross section shown in Fig. Q1(b) is formed from a sheet of stainless steel of 3 mm thickness. The radii c₁ = 150 mm and c₂ = 100 mm are measured to the center line of the sheet metal. Knowing that a torque of magnitude T = 3 kNm is applied to the tube, determine (i) the maximum shearing stress in the tube (ii) the magnitude of the torque carried by the outer circular shell Neglect the dimension of the small opening where the outer and inner shells are connected. Hint: q - T 2A q=rt, T = Fr. Fig. Q1(b)
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tsquare/Tcircle of the shear stresses. Given: r = 11 mm, S = 18 mm, and t = 2.53 mm. S
A 0.500 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 9.3 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft. 3 Answer: Tmax = psi 1/3