A compound curve has the following data: I, = 28°,I, = 31°,D, = 3°, and D, = 4°. Find thestationing of PCc. Use Sta PI = 30 + 120.5.%3Da. 30 + 110.73b. 30 + 118.46C. 30 + 114.88d. 30 + 106.97

To Find Stationing of PCC Given I1= 28° I2 = 31° D1 = 3° D2 = 4° P.I sta = 30+120.5

A compound curve has the following data: I = 28°, I2 = 31°, D1 = 3°, and D2 = 4°. Find the stationing of PCC. Use Sta PI = 30 + 120.5. %3D a. 30 + 110.73 b. 30 + 118.46 C. 30 + 114.88 d. 30 + 106.97

A compound curve has the following data: I = 28°, I2 = 31°, D1 = 3°, and D2 = 4°. Find the stationing of PCC. Use Sta PI = 30 + 120.5. %3D a. 30 + 110.73 b. 30 + 118.46 C. 30 + 114.88 d. 30 + 106.97

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Using Area Moment Method (AMM), with R4= 110 k (upward) and MA= 580 k-ft (counter-clockwise),…

Q: determine the slope at point B in radian. The equation of elastic curve are the following: E = 200…

Q: Q1/ Find the slope of the line : 3x + 4y = 12. x+3= the slope is y=- m=--

A: Given: The equation of line is, 3x+4y=12 The slope of the line is to be determined.

Q: 15. Compute the resultant of the three forces shown in the figure. A. 894.32 N B. 836.90 N C. None…

Q: AB and CB are tangents. If y 137.20 mm and ZABC 67.0°, find: a) 21 -y 21 b) x C

A: Step 1

Q: Determine the resultant R. Compute magnitude, sense and angle of inclination with horizontal x.

A: force F1=350kipforce F2=300kip

Q: (H.W) Find the angle (0) that satisfies the de |1+ sin²0 sin?0 sin?0 cos?0 4 sin 20 1+ cos?0 cos²0 4…

Q: A cyclic quadrilateral ABCD is circumscribing a circle having a center at point O. Angle AOC is…

A: Given: Cyclic quadrilateral circumscribing a circle, Angle AOC= 183058', AB = 50m, BC = 90m, AD =…

Q: Compute the flexural stress (MPa) in the steel for the beam shown using transformed-area method.…

Q: Determine ly and I, for the region shown. Note that the region is symmetric about the x-axis. 68 mm…

Q: 30 kN 50 kN to B D A 1 m 3 m 2 m Figure P-403

Q: Use moment area method to determine the slopes and deflections at points asked? 2-a) find deflection…

A: Given Data Determine the slope and deflection at point B and C using moment area method.

Q: Q2) In the figure shown, find the direction from point M into point P, if you know the direction the…

A: Surveying is the branch of civil engineering including the amount of road scale and construction…

Q: 1. A dumpy level with an internal focusing telescope was set up on the left bank of a river and rod…

Q: Consider the line 6x-3y=4. What is the slope of a line parallel to this line? What is the slope of a…

A: Given:- Equation of line is 6x - 3y = 4

Q: If the elevation of A (benchmark) is 45.074 m, formulate A, B, L and X matrices to adjust the…

A: Given:- The elevation of point A (benchmark) = 45.074 m The following leveling is also given From…

Q: am shown, use double integration method to slope at "B" ite steps) 201 EI = Constant EI dy = ±EI

Q: 400 Problem 2 200 N Compute the magnitude and direction (angle measured from the positive x-axis) of…

Q: IN THE FIGURE, THE WIDTH OF A RIVER BEING OBSERVED IS 63m. ASSUMING THE TRANSIT BEING USED HAS AN…

Q: Using the theorem castilgliano, calculate the horizontal displacement of point D with Castigliano's…

A: Assigning Pseudo load 'P' at D as shown in diagram, P=0

Q: Compute the flexural stress (MPa) in the steel for the beam shown using transformed-area method.…

A: Given : Area of one bar of 36 mm in tension zone = 1006 mm2Numbers of bars in tension zone = 4Total…

Q: For the beam shown, determine the slope at B using conjugate beam method. Please be clear with your…

Q: +y B A 20.0° 60.0° +x C The three displacement vectors in the drawing have magnitudes of A-4.75 m. B…

A: Step 1: Step 2: Step 3: Step 4:Step 5:Step 6:Step 7:

Q: 1) A post is supported by a guy wire which exerts a pull of 100 N on the top of the post. If the…

Q: by the analytical method and Mohr’s circle Find εx' , εy' and γx'y' Find main directions θp and main…

A: Strain in x-direction (εx) = 0Strain in y-direction (εy) = 0Shear strain xy direction (γxy) = 100 μs

Q: B. y = ce4* A. y = c,e 4* (D2 – 3D – 4)y = 30e4* A. y = ce4* + cze¯* +e* 10 B. y = ce4* + cze-* +…

Q: Determine the value of the slope at C in degrees. Answer in decimals (1 degree 1rad*180/pi) 6kN 4KN…

Q: 2/87 If the resultant of the two forces and couple M passes through point O, determine M. 150 09 uru…

A: answer = 148 N-m explanation is given in below step

Q: Using Moment Area Method, determine the deflection at the point of application of the couple. 1200 N…

A: Given data:

Q: 5(y")² + 10(y')³ = 3x -y d²y dt² y"" +3y' +2y=x² 8²v ἂν = +1 ay² ax d²y dx² +(5t + 1)² = 0 DEPENDENT…

A: Whenever we differentiate a variable with respect to another variable, the variable which gets…

Q: FIGURE, THE WIDTH OF A RIVER BEING OBSERVED IS 63m. ASSUMING THE TRANSIT BEING USED HAS AN EXTERNAL…

A: Given Staff intercept at R = s = 0.8. K = 95 , c= 0 Width of river = 63 m

Q: Given the following data in a sample D = 5°, Sta PC = 1+234.56. Azimuth of the back and forward…

Q: From figure 07 for questions 7A and 7B, is a cantilever beam with variable moment of inertia, and E…

Q: 39- 51 55 53 31 39.995 Solve for the length of the check base BE through the Strength of Figures…

A: In a triangle sides opposite to equal angles are also equal

Q: Given the figure below, assume that the E-200 GPa and I = 60x10 mm. Determine the following. A B FL…

A: Given:Required:Deviation of C with respect to tangent drawn from ASlope at ADeflection at CNote: As…

Q: A shunt pipe placed horizontally is shown on the right. The average velocity of section 1 is V1 =…

A: V1 = 3.50 m/s D1 = 0.15 m, A1 = π4 x 0.152= 0.177 m2 D2 = 0.076 m, A2 =π4 x 0.0762=0.00454 m2 D3 =…

Q: SITUATION: A block weighing B00 N is acted upon by a force Pas shown. Knowing that the coefficient…

A: given data weight of block = 800 N static friction coefficient = 0.35 kinematic friction…

Q: Find the distance of AB = S (m) and azimuth (AB) in grad between two points whose coordinates are…

A: Given, Point X(m) Y(m) A 67452.79 42356.25 B 74523.65 64526.63

Q: Assume that w = 73 N/m, L = 2 m, and EI is constant for the beam. Find the slope at the midpoint x =…

A: GIVEN DATA Intensity of load, w=73 N/m length of beam, L=2m EI is constant. The slope of cantilever…

Q: Part 1 (Slope and Deflection of Beams) Problem 1. Solve the problem using Moment Area Method…

A: To determine slope and deflection at D

Q: F2 -F, →X F F At point O in the figure . F1 = 27i +29j F2 = -32 i +14j F3 %3D -16 і - 8 j F4 = -24 i…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

100%

A compound curve has the following data: I, = 28°,I, = 31°,D, = 3°, and D, = 4°. Find the
stationing of PCc. Use Sta PI = 30 + 120.5.
%3D
a. 30 + 110.73
b. 30 + 118.46
C. 30 + 114.88
d. 30 + 106.97

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1vv

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the centroid x-coordinate for the area shown below with respect to the given axis. Given a = 39 mm; b = 234 mm and d = 273 mm. %3D %3D %3D b a a 2a За 2a d a a A. 175.50 mm B. 148.20 mm C. 191.10 mm D. 157.75 mm
help me asap pls :((
by the analytical method and Mohr’s circle Find σx' ,σy' and τx'y'
Q2) a.) Find the intersection coordinates of lines passing from AC and BD. b.) Find the area defined by the corner points A, B, C, and D. The Lengths in the below given figure are in meters. Use Gauss Method only. 17.42 B e----165.05 37.15 55.98 Yp Хр 39.47 22.75L D ol4.90 i 13.90 A 0.00 ty
H D (2 Z G O ye P E Ze Xe F B y A X For the diagram above, given that coordinates G = (0, 0, 0.04), E = (0.08, 0.2, 0.04) and D = (0.08,0,0) metres and P = 20 N, determine the following: The y component of the position vector,FED = -0.2 m. The z component of the position vector,TED. = -0.04 m The magnitude of the position vector,TED. = 0.204 m. The y component of the position vector, UED = -0.200 m The z component of the position vector, UED = -0.040 1. The y component of the force vector P. Please provide the answer in Newtons and report to three significant figures. 2 The z component of the force vector P. Please provide the answer in newtons and report to three significant figures.
Compute the angle 0 in the below figure (in grad), if you know the directions in grads QaB=129.2983° and ɑBc=247.14038 (Example answer 35.2345) A B Answer:
X
Using Area Moment Method (AMM), Calculate the change in slope between tangent lines drawn at points A and C, i.e. BAc in terms of EI? 75 KN A В 2 m 3 m
Find the stations and chainages of PC and PT. Ch= 2742.60 A = 120° TP1 R = 500 TP2
Locate the intersection of Resultant with the x-axes as shown in the figure.
SOLVE EACH PROBLEM USING THE FF. METHODS:• VIRTUAL WORK METHOD• CASTIGLIANO THEOREM the 2nd picture is the answer key
From the figure shown, find the slope at Cin kNm2/EL. El is constant 2 m 20 kN 1256 5:23 62.82 17 67