Answered: determine the slope at point B in…

determine the slope at point B in radian. The equation of elastic curve are the following: E = 200 GPa, I = 1660 x 10^6 mm^4 Let w = 118kN/m, L = 13m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

J 6
Note:Hand written solution not allowed.
If beam as shown in Figure has a rectangular section with a depth of 100mm and width of 20mm, calculate the slope and deflection at free end. Assume E = 200GPa.where P=55
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the slope at A, (c) the slope at B, and (d) the deflection at midspan. Assume that EI is constant for the beam. Let M0 = 45 kN·m, L = 4.5 m, E = 220 GPa, and I = 145 x 106 mm4. Draw a free body diagram of the beam and solve the reaction forces Ay and By. The diagram shows these forces in their positive directions. Your answers may be negative.
I need the answer as soon as possible
Develop the generalized piecewise equation for the elastic curve for the beam as a function of x referenced from A. Your equation should be in terms of P, x, and L. Take EI as a constant. NOTE: A is a pin support and B is a roller. Plot the deflected shape in excel for P = 10 kips, L = 15 ft, E = 29,000 ksi, and I = 150 in^4. Plot using 0.5 ft. increments for x.
A uniform concrete slab is supported by the two cables as shown. Compute the vertical displacement of the concrete slab. steel Area=300sq.mm L=5m 1m P=18N 4m W=25N Aluminum Area 500sq.mm L=3m
5 decimal placesss 1. A bar of 16-mm in diameter is only allowed to decrease at a maximum of 4.84% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 630 MPa, and the Poisson's ratio as 0.36.
rd Determine the slope at point C of the beam in the figure below. Assume the material's modulus of elasticity is 200 GPa, the beam's moment of inertia = 360x106 mm4. 20 kN D 3 m 3 m 6 m II !!
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, and (b) the deflection at B. Assume that El is constant for the beam. Let w = 13 kN/m, L= 5.0 m, E = 210 GPa, and 1= 125 x 10 mm Answer: (b) VB= ·L/2 B mm -L/2 X
A beam is subjected to equal bending moments of Mz = 3100 N·m. The cross-sectional dimensions are b = 180 mm, c = 35 mm, d = 70 mm, and t = 7 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative.
A beam is subjected to equal bending moments of M₂ = 4300 N·m. The cross-sectional dimensions are b = 120 mm, c = 33 mm, d = 67 mm, and t = 4 mm. Determine: (a) the centroid location (measured with respect to the bottom of the cross-section), the moment of inertia about the z axis, and the controlling section modulus about the z axis. (b) the bending stress at point H. Tensile stress is positive, while compressive stress is negative. (c) the bending stress at point K. Tensile stress is positive, while compressive stress is negative. (d) the maximum bending stress produced in the cross section. Tensile stress is positive, while compressive stress is negative. Answer: (a) y= i mm M 1₂ = i mm4 S= mm³ (b) OH = i MPa (c) OK = i MPa (d) gmax= i MPa (typ) b H K