A composite cube with 40-mm sides and the properties shown is made with glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to a tensile load of 65 kN in the x direction. Determine (b) the stresses o, ay, and o, E =50 GPa E, = 15.2 GPa E = 15.2 GPa - 0.254 M0.254 V= 0.428 The stresses a, ay, and o, are , and MPa, respectively. (up to 1st decimal place please).

A composite cube with 40-mm sides and the properties shown is made with glass polymer fibers aligned in the x direction. The cube is constrained against deformations in the y and z directions and is subjected to a tensile load of 65 kN in the x direction. Determine (b) the stresses o, ay, and o, E =50 GPa E, = 15.2 GPa E = 15.2 GPa - 0.254 M0.254 V= 0.428 The stresses a, ay, and o, are , and MPa, respectively. (up to 1st decimal place please).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Let's consider a rod having a solid circular cross-section with diameter of 5 mm and it is made of a material having a Young's modulusE=120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 4.995 mm. determine the applied force F.
Please give me the solution, don't waste my question if you don't really knownthe solution. I will vote it up for you thanks.
3. A steel rod of 3 cm diameter and 5 m length is connected to two grips and the rod is held at a temperature of 95 °C. Determine the stress in the rod, and the force in the rod if the temperature drops to 30 °C for the following cases a. The grip ends do not yield b. The grip ends yield by 0.12 cm Assume the Young's Modulus of the rod is E = 2×105 MPa, and the CTE is a=12×106/ °C
Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young’s modulus E = 200 Gpa and a Poisson’s ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.995 mm. determine the applied force F.
Simple stressa nd strain problem! Pleasee help
SHOW ILLUSTRATION AND SOLUTION Problem 2: Steel railroad rails 10 m long are laid with a clearance of 3 mm at atemperature of 15 oC. E = 200 GPa and  = 11.7 x 10 - 6/oC. 1. At what temperature will the rails just touch?2. What stress would be induced in the rails at that temperature if there were no initial clearance?
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
Reg.no: 5395 MOS-2
Figure Q4 (a) shows an L-bracket ABC with diameter d which lies in the horizontal plane. It is made from a material with elastic and shear moduli E and G, respectively. If a vertical load P is applied at end C, determine the total strain energy that is stored in the whole structure. Express your answer in terms of P, E, G, d and L. Neglect the strain energy due to shear force.
4. For an element subjected to stresses of x= 70 ksi y=-15 ksi xy=30 ksi SAH: (a) Draw Mohr's circle (b) Calculate the value of the principal stresses
Don't waste my question please, I need the solution don't just capy the answer that I give there.
A cylinder of (320) mm inside diameter and (64) mm thickness is subjected to an internal pressure of 15 MPa. Find the variation of circumferential and radial stresses in the shell and plot them. What is the increase in the inside and outside diameters of the shell? Take E=200 GPa and v=0.3