A closed system containing Nitrogen gas in a piston-cylinder arrangement, as shown in the below figure, is undergoing a cyclic process composed of three processes in series as stated below: Process 1-2: Compression at constant pressure from p1 =159 kPa, V1 = 0.11 m to state 2. Process 2-3: Heat addition at constant volume to state 3, where p3 = 359 kPa. Process 3-1: Expansion to the initial state, during which the pressure-volume relationship is PV = constant. a) Evaluate the volume at state 2, in m3, and b) Determine the work for each process, in kJ. Nitrogen

A closed system containing Nitrogen gas in a piston-cylinder arrangement, as shown in the below figure, is undergoing a cyclic process composed of three processes in series as stated below: Process 1-2: Compression at constant pressure from p1 =159 kPa, V1 = 0.11 m to state 2. Process 2-3: Heat addition at constant volume to state 3, where p3 = 359 kPa. Process 3-1: Expansion to the initial state, during which the pressure-volume relationship is PV = constant. a) Evaluate the volume at state 2, in m3, and b) Determine the work for each process, in kJ. Nitrogen

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the minimum work done per Kg of air in a cycle according to the following process: a. isothermal expansion from state 1 to state 2 b. Constant volume compression form state 2 to state 3 c. Constant pressure compression from state 3 to the initial state Data: P1= 350KPa T3= 1650⁰C V1 = 1 m³/Kg represent the work in a P-V diagram
p62,#13 with illustration and explanation
20 g of air undergoes a closed cycle, illustrated in Figure Q2, which consists of the following 3 processes: 1-2 Constant pressure heat rejection. 2-3 Constant volume heat addition. 3-1 Isothermal expansion back to the original conditions. P (kPa) 75 1 V (m') 0.025 0.04 Figure Q2: Three process cycle Given that Rair = 287 J/kg-K, and Cy = 718 J/kg-K, and assuming ideal gas conditions throughout: (a) Determine the temperatures at points 1, 2 and 3, and the pressure at point 3. (b) Determine the work during each process, and the net work from the cycle. (c) Determine the heat transferred during each process. (d) Verify that this is a cycle.
A closed system consists of gas of 2 kg initially in state 1 with p1 4bar and specific volume V1 = 1m /kg. The system undergoes a power cycle consisting of the following processes: Process 1-2: polytropic process to v2 = 2m3 /kg, p2 = 1bar; Process 2-3: isobaric compression to v1; Process 3-1: isochoric process to p1. Draw the cycle on a p – v (specific volume) diagram. Show the system states, cycle direction, and the cycle (net) work.
2. A piston-cylinder assembly with stops (see figure) contains 1.54 kg of water initially occupying a volume of 1.25 m at a pressure of 1 bar (State 1). As the water in the assembly is heated, the pressure and temperature in the system remain constant until the piston contacts the stops. In this position (State 2), the quality, x2, is determined to be 92%. Heat continues to be added to the system at a constant volume until the system reaches a pressure of 1.5 bar (State 3). Determine the following quantities: а. X b. V2 (m2) C. W13 (kJ) d. Qu (kJ) e. Plot the results on a P-v diagram, labelling relevant P, T, and v values.
Air is compressed in a piston-cylinder assembly from p₁ = 10 lb-/in², T₁= 500°R, V₁ = 9 ft³ to a final volume of V₂ = 1 ft³ in a process described by pv¹.30 = constant. Assume ideal gas behavior and neglect kinetic and potential energy effects. Using constant specific heats evaluated at T₁, determine the work and the heat transfer, in Btu. Step 1 Determine the work, in Btu. W12= Save for Later Btu Attempts: 0 of 4 used Step 2 The parts of this question must be completed in order. This part will be available when you complete the part above. Submit Answer
Ammonia in a piston-cylinder assembly undergoes two processes in series. Initially, the ammonia is saturated vapour at P₁=1000 kPa. Process 1-2 involves cooling until the piston meets the stops where the position is locked in place at which time quality is x2=75%. The second process from state 2 to state 3, involves heating (at constant volume) until x3=100%. If the mass is 0.45 kg determine: The work for process 2-3 (in kJ). The heat transfer for process 2-3 (in kJ). Sketch the processes on a p-v diagram, what does the area under the curve represent?
In the piston-cylinder system shown in the figure, the piston rises up to (3) position. Choosing one of the 3 options given in the table, a) the pressure and temperature in positions (2, 3), b) Show the process change (1-2, 2-3) on the P-v diagram by drawing the saturation actions, c) find the total limit work and spring work, d) Find the heat transferred.
Show step by step
One kilogram of an ideal gas at 5.5 bar with an initial volume of 0.3 m expands to a final volume of 0.5 m in accordance with the equation 13 pV = C. Find the heat transfer during the process. Take R = 0.287 kJ/kg-K and C¸ = 0.713 kJ/kg-K.
A 300-lb iron casting. initially at 600°F, is quenched in a tank filled with 2121 lb of oil, initially at 80°F. The iron casting and oil can be modeled as incompressible with specific heats 0.10 Btu/lb - °R. and 0.45 Btu/lb - °R, respectively. (a) For the iron casting and oil as the system.determine the final equilibrium temperature, in °F. Ignore heat transfer between the system and its surroundings. °F (b) For the iron casting and oil as the system,determine the amount of entropy produced within the tank, in Btu/°R. Ignore heat transfer between the system and its surroundings. Btu/°R